ACS8525ALC datasheet(9/112 Pages) SEMTECH

9 / 112 page

ACS8525A LC/P

ADVANCED COMMS & SENSING

FINAL

DATASHEET

Revision 1.00/September 2007 © Semtech Corp.

Page 9

www.semtech.com

PECL/LVDS Input Port Selection

The choice of PECL or LVDS compatibility is programmed

via the cnfg_differential_inputs register. Unused PECL

differential inputs should be fixed with one input High

(VDD) and the other input Low (GND), or set in LVDS mode

and left floating, in which case one input is internally

pulled High and the other Low.

Input Locking Frequency Modes

Each input port has to be configured to receive the

expected input frequency. To achieve this, three Input

Locking Frequency modes are provided: Direct Lock,

Lock8K and DivN.

Direct Lock Mode

In Direct Lock mode, DPLL1 can lock to the selected input

at the spot frequency of the input, for example 19.44 MHz

performs the DPLL phase comparisons at 19.44 MHz.

In Lock8K and DivN modes (and for the special case of

155 MHz), an internal divider is used prior to DPLL1 to

divide the input frequency before it is used for phase

comparisons.

Direct Lock Mode 155 MHz.

The max frequency allowed for phase comparison is

77.76 MHz, so for the special case of a 155 MHz input set

to Direct Lock mode, there is a divide-by-two function

automatically selected to bring the frequency down to

within the limits of operation.

Lock8K Mode

Lock8K mode automatically sets the divider parameters

to divide the input frequency down to 8 kHz. Lock8K can

only be used on the supported spot frequencies (see

Table 4 Note(i)). Lock8k mode is enabled by setting the

Lock8k bit (Bit 6) in the appropriate

cnfg_ref_source_frequency register location. Using lower

frequencies for phase comparisons in the DPLL results in

a greater tolerance to input jitter. It is possible to choose

which edge of the input reference clock to lock to, by

setting 8K Edge Polarity (Bit 2 of Reg. 03, test_register1).

DivN Mode

In DivN mode, the divider parameters are set manually by

configuration (Bit 7 of the cnfg_ref_source_frequency

division is 8 kHz.

The DivN function is defined as:

DivN = “Divide by N + 1”, i.e. it is the dividing factor used

for the division of the input frequency, and has a value of

(N + 1) where N is an integer from 1 to 15624 inclusive.

Therefore, in DivN mode the input frequency can be

divided by any integer value between 2 to 15625.

Consequently, any input frequency which is a multiple of

8 kHz, between 8 kHz and 125 MHz, can be supported by

using DivN mode.

Note...Any reference input can be set to use DivN

independently of the frequencies and configurations of the

other inputs. However only one value of N is allowed, so all

inputs with DivN selected must be running at the same

frequency.

DivN Examples

(a) To lock to 2.000 MHz:

(i)

Set the cnfg_ref_source_frequency register to

10XX0000 (binary) to enable DivN, and set the

frequency to 8 kHz - the frequency required after

division. (XX = “Leaky Bucket” ID for this input).

(ii) To achieve 8 kHz, the 2 MHz input must be

divided by 250. So, if DivN = 250 = (N + 1)

then N must be set to 249. This is done by writing

F9 hex (249 decimal) to the DivN register pair

Reg. 46/47.

(b) To lock to 10.000 MHz:

(i)

The cnfg_ref_source_frequency register is set to

10XX0000 (binary) to set the DivN and the

frequency to 8 kHz, the post-division frequency.

(XX = “Leaky Bucket” ID for this input).

(ii) To achieve 8 kHz, the 10 MHz input must be

divided by 1,250. So, if DivN, = 250 = (N+1)

then N must be set to 1,249. This is done by

writing 4E1 hex (1,249 decimal) to the DivN

Input SEC Activity Monitors

An input reference activity monitor is assigned to each of

the three SEC inputs. The monitors operate continuously

such that at all times the activity status of each SEC input

is known.

SEC activity monitoring is used to declare whether or not

an input is valid. Any SEC that suffers a loss-of-activity will

be declared as invalid and unavailable for selection.

SEC activity monitoring is a continuous process which is

used to identify clock problems. There is a difference in

ACS8525ALC датащи(PDF) 9 Page - Semtech Corporation

ACS8525ALC датащи(HTML) 9 Page - Semtech Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL