USB2524 datasheet(23/57 Pages) SMSC

23 / 57 page

USB MultiSwitchTM Hub

Datasheet

SMSC USB2524

Revision 1.91 (08-22-07)

DATASHEET

7.1.4.7

BIT

NUMBER

BIT NAME

DESCRIPTION

SELF_BUS_PWR

Self or Bus Power: Selects between Self- and Bus-Powered operation.

The Hub is either Self-Powered (draws less than 2mA of upstream bus power)

or Bus-Powered (limited to a 100mA maximum of upstream power prior to

being configured by the host controller).

When configured as a Bus-Powered device, the SMSC Hub consumes less

than 100mA of current prior to being configured. After configuration, the Bus-

Powered SMSC Hub (along with all associated hub circuitry, any embedded

devices if part of a compound device, and 100mA per externally available

downstream port) must consume no more than 500mA of upstream VBUS

current. The current consumption is system dependent, and the OEM must

ensure that the USB 2.0 specifications are not violated.

When configured as a Self-Powered device, <1mA of upstream VBUS current

is consumed and all ports are available, with each port being capable of

sourcing 500mA of current.

This field is set by the OEM using either the SMBus or EEPROM interface

options.

Please see the description under Dynamic Power for the self/bus power

functionality when dynamic power switching is enabled.

0 = Bus-Powered operation.

1 = Self-Powered operation.

Note:

If Dynamic Power Switching is enabled, this bit is ignored and the

SELF_PWR pin is used to determine if the hub is operating from self

or bus power.

Reserved

Reserved, always = ‘0’.

HS_DISABLE

High Speed Disable: Disables the capability to attach as either a High/Full-

speed device, and forces attachment as Full-speed only i.e. (no High-Speed

support).

0 = High-/Full-Speed.

1 = Full-Speed-Only (High-Speed disabled!)

MTT_ENABLE

Multi-TT enable: Enables one transaction translator per port operation.

Selects between a mode where only one transaction translator is available for

all ports (Single-TT), or each port gets a dedicated transaction translator (Multi-

TT) {Note: The host may force Single-TT mode only}. When using the internal

default option, the MTT_EN pin enables/disables MTT support.

0 = single TT for all ports.

1 = one TT per port (multiple TT’s supported)

EOP_DISABLE

EOP Disable: Disables EOP generation of EOF1 when in Full-Speed mode.

During FS operation only, this permits the Hub to send EOP if no downstream

traffic is detected at EOF1. See Section 11.3.1 of the USB 2.0 Specification for

additional details. Note: generation of an EOP at the EOF1 point may prevent

a Host controller (operating in FS mode) from placing the USB bus in suspend.

0 = An EOP is generated at the EOF1 point if no traffic is detected.

1 = EOP generation at EOF1 is disabled (note: this is normal USB operation).

2:1

CURRENT_SNS

Over Current Sense: Selects current sensing on a port-by-port basis, all ports

ganged, or none (only for bus-powered hubs) The ability to support current

sensing on a port or ganged basis is hardware implementation dependent.

00 = Ganged sensing (all ports together).

01 = Individual port-by-port.

1x = Over current sensing not supported. (must only be used with Bus-

Powered configurations!)

PORT_PWR

Port Power Switching: Enables power switching on all ports simultaneously

(ganged), or port power is individually switched on and off on a port- by-port

basis (individual). The ability to support power enabling on a port or ganged

basis is hardware implementation dependent.

0 = Ganged switching (all ports together)

1 = Individual port-by-port switching.

USB2524 датащи(PDF) 23 Page - SMSC Corporation

USB2524 датащи(HTML) 23 Page - SMSC Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57

датащи скачать

ссылки URL