LP3871, LP3874

www.ti.com

SNVS225H – FEBRUARY 2003 – REVISED JUNE 2015

6.5 Electrical Characteristics

Unless otherwise specified: TJ = 25°C, VIN = VO(NOM) + 1 V, IL = 10 mA, COUT = 10 µF, VSD = 2 V.

PARAMETER

TEST CONDITIONS

MIN(1)

TYP(2)

MAX(1)

UNIT

Output voltage tolerance(3)

VOUT + 1 V ≤ VIN ≤ 7 V, 10 mA ≤ IL ≤ 0.8 A

–1.5%

0%

1.5%

VOUT

VOUT + 1 V ≤ VIN ≤ 7 V, 10 mA ≤ IL ≤ 0.8 A,

–3%

3%

–40°C

≤ TJ ≤ 125°C

Output voltage line regulation(3)

VOUT + 1 V ≤ VIN ≤ 7 V

0.02%

ΔVOL

VOUT + 1 V ≤ VIN ≤ 7 V, –40°C ≤ TJ ≤ 125°C

0.06%

Output voltage load regulation(3)

10 mA

≤ IL ≤ 0.8 A

0.04%

ΔVO/

ΔIOUT

10 mA

≤ IL ≤ 0.8 A, –40°C ≤ TJ ≤ 125°C

0.1%

IL = 80 mA

24

35

IL = 80 mA, –40°C ≤ TJ ≤ 125°C

40

VIN –

Dropout voltage(4)

mV

VOUT

IL = 0.8 A

240

300

IL = 0.8 A, –40°C ≤ TJ ≤ 125°C

350

IL = 150 mA

5

9

IL = 150 mA, –40°C ≤ TJ ≤ 125°C

10

Ground pin current in normal

IGND

mA

operation mode

IL = 0.8 A

6

14

IL = 0.8 A, –40°C ≤ TJ ≤ 125°C

15

Ground pin current in shutdown

VSD ≤ 0.3 V

0.01

10

µA

IGND

mode

–40°C

≤ TJ ≤ 85°C

50

IO(PK)

Peak output current

VOUT ≥ VO(NOM) – 4%

1

A

SHORT CIRCUIT PROTECTION

ISC

Short-circuit current

2.3

A

SHUTDOWN INPUT

Output = High

VIN

Output = High, –40°C

≤ TJ ≤ 125°C

2

VSDT

Shutdown threshold

V

Output = Low

0

Output = Low, –40°C

≤ TJ ≤ 125°C

0.3

TdOFF

Turnoff delay

IL = 0.8 A

20

µs

TdON

Turnon delay

IL = 0.8 A

25

µs

ISD

SD input current

VSD = VIN

1

nA

ERROR FLAG

Threshold

See(5)

10%

VT

See(5), –40°C

≤ TJ ≤ 125°C

5%

16%

Threshold hysteresis

See(5)

5%

VTH

See(5), –40°C

≤ TJ ≤ 125°C

2%

8%

Isink = 100 µA

0.02

VEF(Sat)

ERROR flag saturation

V

Isink = 100 µA, –40°C ≤ TJ ≤ 125°C

0.1

Td

Flag reset delay

1

µs

Ilk

ERROR flag pin leakage current

1

nA

Imax

ERROR flag pin sink current

VError = 0.5 V

1

mA

(1)

Limits are specified by testing, design, or statistical correlation.

(2)

Typical numbers are at 25°C and represent the most likely parametric norm.

(3)

Output voltage line regulation is defined as the change in output voltage from the nominal value due to change in the input line voltage.

Output voltage load regulation is defined as the change in output voltage from the nominal value due to change in load current. The line

and load regulation specification contains only the typical number. However, the limits for line and load regulation are included in the

output voltage tolerance specification.

(4)

Dropout voltage is defined as the minimum input to output differential voltage at which the output drops 2% below the nominal value.

Dropout voltage specification applies only to output voltages of 2.5 V and above. For output voltages below 2.5 V, the dropout voltage is

nothing but the input to output differential, because the minimum input voltage is 2.5 V.

(5)

ERROR Flag threshold and hysteresis are specified as percentage of regulated output voltage. See ERROR Flag Operation.

Copyright © 2003–2015, Texas Instruments Incorporated

Submit Documentation Feedback

5

Product Folder Links: LP3871 LP3874