M41T83RM6F datasheet(44/64 Pages) STMICROELECTRONICS

44 / 64 page

Clock operation

M41T82, M41T83

44/64

DocID012578 Rev 19

3.12

Oscillator fail detection

If the oscillator fail (OF) bit is internally set to a '1,' this indicates that the oscillator has either

stopped, or was stopped for some period of time. This bit can be used to judge the validity of

the clock and date data. This bit will be set to '1' any time the oscillator stops.

In the event the OF bit is found to be set to '1' at any time other than the initial power-up, the

STOP bit (ST) should be written to a '1,' then immediately reset to 0. This will restart the

oscillator. The following conditions can cause the OF bit to be set:

•

The first time power is applied (defaults to a '1' on power-up).

Note:

If the OF bit cannot be written to '0' four seconds after the initial power-up, the STOP bit (ST)

should be written to a '1,' then immediately reset to 0.

•

The voltage present on VCC or battery is insufficient to support oscillation.

•

The ST bit is set to '1.'

•

External interference of the crystal

For the M41T83, if the oscillator fail interrupt enable bit (OFIE) is set to a '1,' the

IRQ1/FT/OUT pin will also be asserted (see Section 3.13 and Section 3.14 for additional

conditions which apply). The IRQ1/FT/OUT output is de-asserted by resetting the OF bit to

0, NOT by reading the flags register. The OF bit will remain a '1' until written to 0. Reading

the flags register has no effect on OF.

The oscillator must start and have run for at least 4 seconds before attempting to reset the

OF bit to 0.

The oscillator fail detect circuit funtions during backup mode. If a triggering event occurs to

disrupt the oscillator during a power-down condition, the OF bit will be set accordingly.

3.13

Oscillator fail interrupt enable (M41T83 only)

With the OFIE bit set, the OF bit will cause the IRQ1/FT/OUT output to be asserted (see

Section 3.14.1

and 3.14.2 for additional conditions that apply). The IRQ1/FT/OUT output is

cleared by resetting the OF bit to 0 (NOT by reading the flags register). Clearing the OFIE

bit will also cause the IRQ1/FT/OUT output to de-assert, but if OFIE is subsequently set

prior to clearing OF, the IRQ1/FT/OUT output will assert immediately upon setting OFIE.

Clearing the OF bit is necessary to prevent such an inadvertent interrupt.

If the alarm in backup enable bit, ABE, is set (along with OFIE), the oscillator fail detect will

cause an interrupt in the IRQ1/FT/OUT pin during backup mode. For additional information

on this, refer to Section 3.14.2.

3.14

IRQ1/FT/OUT pin, frequency test, interrupts and the OUT bit

(M41T83 only)

Four interrupt sources, the frequency test function, and the discrete output bit OUT all share

the IRQ1/FT/OUT pin. Priority is built into the part such that some functions dominate

others. Additionally, the priority depends on configuration bits such as OUT and ABE, and

on whether the part is operating on VCC or is in the backup mode. This pin is an open drain

output and requires an external pull-up resistor.

Figure 25

shows the various signal sources and controlling bits for the IRQ1/FT/OUT output

pin.

M41T83RM6F датащи(PDF) 44 Page - STMicroelectronics

M41T83RM6F датащи(HTML) 44 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64

датащи скачать

ссылки URL