| поискавой системы для электроныых деталей |
|
DSPIC30F3012AT20E/ML датащи(PDF) 132 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
DSPIC30F3012AT20E/ML датащи(HTML) 132 Page - Microchip Technology |
|
132 / 205 page ![]() dsPIC30F2011/2012/3012/3013 DS70139E-page 130 © 2006 Microchip Technology Inc. Any interrupt that is individually enabled (using the cor- responding IE bit) and meets the prevailing priority level will be able to wake-up the processor. The processor will process the interrupt and branch to the ISR. The Sleep Status bit in the RCON register is set upon wake-up. All Resets will wake-up the processor from Sleep mode. Any Reset, other than POR, will set the Sleep Status bit. In a POR, the Sleep bit is cleared. If the Watchdog Timer is enabled, then the processor will wake-up from Sleep mode upon WDT time-out. The Sleep and WDTO Status bits are both set. 17.6.2 IDLE MODE In Idle mode, the clock to the CPU is shut down while peripherals keep running. Unlike Sleep mode, the clock source remains active. Several peripherals have a control bit in each module that allows them to operate during Idle. LPRC Fail-Safe Clock remains active if clock failure detect is enabled. The processor wakes up from Idle if at least one of the following conditions has occurred: • any interrupt that is individually enabled (IE bit is ‘1’) and meets the required priority level • any Reset (POR, BOR, MCLR) • WDT time-out Upon wake-up from Idle mode, the clock is re-applied to the CPU and instruction execution begins immedi- ately, starting with the instruction following the PWRSAV instruction. Any interrupt that is individually enabled (using IE bit) and meets the prevailing priority level will be able to wake-up the processor. The processor will process the interrupt and branch to the ISR. The Idle Status bit in the RCON register is set upon wake-up. Any Reset other than POR will set the Idle Status bit. On a POR, the Idle bit is cleared. If Watchdog Timer is enabled, then the processor will wake-up from Idle mode upon WDT time-out. The Idle and WDTO Status bits are both set. Unlike wake-up from Sleep, there are no time delays involved in wake-up from Idle. 17.7 Device Configuration Registers The Configuration bits in each device Configuration register specify some of the device modes and are programmed by a device programmer, or by using the In-Circuit Serial Programming™ (ICSP™) feature of the device. Each device Configuration register is a 24-bit register, but only the lower 16 bits of each regis- ter are used to hold configuration data. There are four device Configuration registers available to the user: 1. FOSC (0xF80000): Oscillator Configuration Register 2. FWDT (0xF80002): Watchdog Timer Configuration Register 3. FBORPOR (0xF80004): BOR and POR Configuration Register 4. FGS (0xF8000A): General Code Segment Configuration Register The placement of the Configuration bits is automati- cally handled when you select the device in your device programmer. The desired state of the Configuration bits may be specified in the source code (dependent on the language tool used), or through the programming interface. After the device has been programmed, the application software may read the Configuration bit values through the table read instructions. For addi- tional information, please refer to the Programming Specifications of the device. Note: In spite of various delays applied (TPOR, TLOCK and TPWRT), the crystal oscillator (and PLL) may not be active at the end of the time-out (e.g., for low-frequency crys- tals). In such cases, if FSCM is enabled, then the device will detect this as a clock failure and process the clock failure trap, the FRC oscillator will be enabled and the user will have to re-enable the crystal oscillator. If FSCM is not enabled, then the device will simply suspend execution of code until the clock is stable and will remain in Sleep until the oscillator clock has started. Note: If the code protection Configuration fuse bits (FGS<GCP> and FGS<GWRP>) have been programmed, an erase of the entire code-protected device is only possible at voltages VDD ≥ 4.5V. |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |