| поискавой системы для электроныых деталей |
|
10F200 датащи(PDF) 68 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
10F200 датащи(HTML) 68 Page - Microchip Technology |
|
68 / 96 page ![]() PIC10F200/202/204/206 DS41239D-page 66 © 2007 Microchip Technology Inc. 12.2 DC Characteristics: PIC10F200/202/204/206 (Extended) DC CHARACTERISTICS Standard Operating Conditions (unless otherwise specified) Operating Temperature -40×C £ TA £ +125×C (extended) Param No. Sym Characteristic Min Typ(1) Max Units Conditions D001 VDD Supply Voltage 2.0 5.5 V See Figure 12-1 D002 VDR RAM Data Retention Voltage(2) 1.5* — V Device in Sleep mode D003 VPOR VDD Start Voltage to ensure Power-on Reset —Vss — V D004 SVDD VDD Rise Rate to ensure Power-on Reset 0.05* — — V/ms IDD Supply Current(3) D010 — — 175 0.63 275 1.1 μA mA VDD = 2.0V VDD = 5.0V IPD Power-down Current(4) D020 — — 0.1 0.35 9 15 μA μA VDD = 2.0V VDD = 5.0V IWDT WDT Current(5) D022 — — 1.0 7 18 22 μA μA VDD = 2.0V VDD = 5.0V ICMP Comparator Current(5) D023 — — 12 42 27 85 μA μA VDD = 2.0V VDD = 5.0 VREF Internal Reference Current(5), (6) D024 — 85 175 120 200 μA μA VDD = 2.0V VDD = 5.0V * These parameters are characterized but not tested. Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25 °C. This data is for design guidance only and is not tested. 2: This is the limit to which VDD can be lowered in Sleep mode without losing RAM data. 3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus loading, bus rate, internal code execution pattern and temperature also have an impact on the current consumption. a) The test conditions for all IDD measurements in active operation mode are: All I/O pins tri-stated, pulled to VSS, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified. b) For standby current measurements, the conditions are the same, except that the device is in Sleep mode. 4: Power-down current is measured with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS. 5: The peripheral current is the sum of the base IDD or IPD and the additional current consumed when this peripheral is enabled. 6: Measured with the Comparator enabled. |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |