DSPIC33FJ12MC02ESS datasheet(168/284 Pages) MICROCHIP

168 / 284 page

dsPIC33FJ12MC201/202

DS70265B-page 166

Preliminary

15.1

Quadrature Encoder Interface

Logic

A typical incremental (or optical) encoder has three

outputs: Phase A, Phase B and an index pulse. These

signals are useful and often required in position and

speed control of ACIM and SR motors.

The two channels, Phase A (QEA) and Phase B (QEB),

have a unique relationship. If Phase A leads Phase B,

the direction of the motor is deemed positive or for-

ward. If Phase A lags Phase B, the direction of the

motor is deemed negative or reverse.

A third channel, termed index pulse, occurs once per

revolution and is used as a reference to establish an

absolute position. The index pulse coincides with

Phase A and Phase B, both low.

15.2

16-bit Up/Down Position

Counter Mode

The 16-bit up/down counter counts up or down on

every count pulse, which is generated by the difference

of the Phase A and Phase B input signals. The counter

acts as an integrator whose count value is proportional

to position. The direction of the count is determined by

the UPDN signal, which is generated by the

Quadrature Encoder Interface logic.

15.2.1

POSITION COUNTER ERROR

CHECKING

Position counter error checking in the QEI is provided

for and indicated by the CNTERR bit (QEICON<15>).

The error checking applies only when the position

counter is configured for Reset on the Index Pulse

modes (QEIM<2:0> = 110 or 100). In these modes, the

contents of the POSCNT register are compared with

the values (0xFFFF or MAXCNT + 1, depending on

direction).

If these values are detected, the CNTERR bit is set,

generating an error condition, and a QEI counter error

interrupt is generated. The QEI counter error interrupt

can

disabled

setting

the

CEID

bit

(DFLTCON<8>).

The position counter continues to count encoder edges

after an error has been detected. The POSCNT regis-

ter continues to count up/down until a natural rollover/

underflow. No interrupt is generated for the natural

rollover/underflow event.

The CNTERR bit is a read/write bit and is reset in

software by the user application.

15.2.2

POSITION COUNTER RESET

The Position Counter Reset Enable bit, POSRES

(QEI<2>), controls whether the position counter is reset

when the index pulse is detected. This bit is applicable

only when QEIM<2:0> = 100 or 110.

If the POSRES bit is set to ‘1’, the position counter is

reset when the index pulse is detected. If the POSRES

bit is set to ‘0’, the position counter is not reset when

the index pulse is detected. The position counter con-

tinues counting up or down, and is reset on the rollover

or underflow condition.

The interrupt is still generated on the detection of the

index pulse and not on the position counter overflow/

underflow.

15.2.3

COUNT DIRECTION STATUS

The QEI logic generates a UPDN signal, based upon

the relationship between Phase A and Phase B. In

addition to the output pin, the state of this internal

UPDN signal is supplied to an SFR bit, UPDN

(QEICON<11>), as a read-only bit. To place the state of

this signal on an I/O pin, the SFR bit, PCDOUT

(QEICON<6>), must be set to ‘1’.

15.3

Position Measurement Mode

Two measurement modes are supported, x2 and x4.

These modes are selected by the QEIM<2:0> mode

select bits located in SFR QEICON<10:8>.

When control bits QEIM<2:0> = 100 or 101, the x2

Measurement mode is selected and the QEI logic only

looks at the Phase A input for the position counter

increment rate. Every rising and falling edge of the

Phase A signal causes the position counter to be

incremented or decremented. The Phase B signal is

still used for the determination of the counter direction.

Within the x2 Measurement mode, there are two

variations of how the position counter is reset:

• Position counter reset by detection of index pulse,

QEIM<2:0> = 100

• Position counter reset by match with MAXCNT,

QEIM<2:0> = 101

When control bits QEIM<2:0> = 110 or 111, the x4

Measurement mode is selected and the QEI logic looks

at both edges of the Phase A and Phase B input

signals. Every edge of both signals causes the position

counter to increment or decrement.

Within the x4 Measurement mode, the position counter

can be reset two ways:

• Position counter reset by detection of index pulse,

QEIM<2:0> = 110.

• Position counter reset by match with MAXCNT,

QEIM<2:0> = 111.

The x4 Measurement mode provides for finer

resolution data (more position counts) for determining

motor position.

DSPIC33FJ12MC02ESS датащи(PDF) 168 Page - Microchip Technology

DSPIC33FJ12MC02ESS датащи(HTML) 168 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL