MCP3909-ISLASHSS datasheet(2/40 Pages) MICROCHIP

2 / 40 page

MCP3909

DS22025A-page 2

1.0

ELECTRICAL

CHARACTERISTICS

Absolute Maximum Ratings †

DD ...................................................................................7.0V

Digital inputs and outputs w.r.t. AGND........ -0.6V to VDD +0.6V

Analog input w.r.t. AGND.........................................-6V to +6V

VREF input w.r.t. AGND ............................... -0.6V to VDD +0.6V

Storage temperature .....................................-65°C to +150°C

Ambient temp. with power applied ................-65°C to +125°C

Soldering temperature of leads (10 seconds) .............+300°C

ESD on the analog inputs (HBM,MM) .................4.0 kV, 400V

ESD on all other pins (HBM,MM) ........................4.0 kV, 400V

† Notice: Stresses above those listed under "Maximum

Ratings" may cause permanent damage to the device. This is

a stress rating only and functional operation of the device at

those or any other conditions above those indicated in the

operation listings of this specification is not implied. Exposure

to maximum rating conditions for extended periods may affect

device reliability.

ELECTRICAL CHARACTERISTICS

Electrical Specifications: Unless otherwise indicated, all parameters apply at AVDD = DVDD = 4.5V to 5.5V,

Internal VREF, HPF turned on (AC mode), AGND, DGND = 0V, MCLK = 3.58 MHz; TA = -40°C to +85°C.

Parameter

Sym

Min

Typ.

Max

Units

Comment

Active Power Measurement Accuracy

Active Energy Measurement

Error

E—

0.1

—

% FOUT Channel 0 swings 1000:1 range,

FOUT0, FOUT1 Frequency outputs

only, does not apply to serial inter-

face data. (Note 1, Note 4)

No-Load Threshold/

Minimum Load

NLT

—

0.0015

—

% FOUT

Max

Frequency outputs only, does not

apply to serial interface data.

Disabled when F2, F1, F0 = 0, 1, 1

(Note 5, Note 6)

System Gain Error

—

% FOUT (Note 2, Note 5)

AC Power Supply Rejection

(output frequency variation)

AC PSRR

—

0.01

—

% FOUT F2, F1, F0 = 0, 1, 1 (Note 3)

DC Power Supply Rejection

(output frequency

variation)

DC PSRR

—

0.01

—

% FOUT HPF = 1, Gain = 1 (Note 3)

Waveform Sampling

A/D Converter Signal-to-

Noise and Distortion Ratio

SINAD

—

Applies to both channels,

VIN = 0 dBFS at 50 Hz

(VIN = Full Scale)

Bandwidth

(Notch Frequency)

—

kHz

Applies to both channels,

MCLK/256

Phase Delay Between

Channels

—

1/MCLK

HPF = 0 and 1, < 1 MCLK period

(Note 4, Note 6, Note 7)

Note 1: Measurement error = (Energy Measured By Device - True Energy)/True Energy * 100%. Accuracy is

measured with signal (±660 mV) on Channel 1. FOUT0, FOUT1 pulse outputs. Valid from 45 Hz to 75 Hz.

See typical performance curves for higher frequencies and increased dynamic range.

2: Does not include internal VREF. Gain = 1, CH0 = 470 mVDC, CH1 = 660 mVDC, difference between

measured output frequency and expected transfer function.

3: Percent of HFOUT output frequency variation; Includes external VREF = 2.5V, CH1 = 100 mVRMS @ 50 Hz,

CH2 = 100 mVRMS @ 50 Hz, AVDD = 5V + 1Vpp @ 100 Hz. DC PSRR: 5V ±500 mV

4: Error applies down to 60 degree lead (PF = 0.5 capacitive) and 60 degree lag (PF = 0.5 inductive).

5: Refer to Section 4.0 “Device Overview” for complete description.

6: Specified by characterization, not production tested.

7: 1 MCLK period at 3.58 MHz is equivalent to less than <0.005 degrees at 50 or 60 Hz.

MCP3909-I/SS датащи(PDF) 2 Page - Microchip Technology

MCP3909-I/SS датащи(HTML) 2 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40

датащи скачать

ссылки URL