| поискавой системы для электроныых деталей |
|
MP5990 датащи(PDF) 21 Page - Monolithic Power Systems |
|
|
|||||||||||||||||||||||||||||
MP5990 датащи(HTML) 21 Page - Monolithic Power Systems |
|
21 / 72 page ![]() MP5990 – 16V, 50A, 1mΩ, INTELLIGENT HOT-SWAP SOLUTION WITH PMBUS MP5990 Rev. 1.1 MonolithicPower.com 21 4/19/2024 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2024 MPS. All Rights Reserved. Figure 5 shows the start-up sequence in LPM. In LPM, ADVANCE_CTRL (F1h), bit[13] selects whether the device should enter the optional MTP copying mode or initiate the system initialization delay time after EN pulls high. If bit[13] is set to 0, then the MP5990 starts TON_DELAY after EN goes high. This sequence is different from regular power mode. VDD33 UVLO On POR + MTP Copying + System Initialization t1 t0 Wait EN On TON_DELAY VIN E-Fuse Insertion Delay t2 t3 t4 t5 t8 340mV t7 SCREF OCWREF VDD33 VDD18 SCREF/ OCWREF EN ON OCREF SS GATE VOUT GOK VGS_TH t6 MTP Copying + System Initialization (Optional) Figure 5: Start-Up Sequence in Low-Power Mode Current-Sense Output (CS) The CS pin provides a current proportional to IOUT flowing through the device. VCS is used for over-current (OC) limiting, OC warning indication, and parallel operation with start-up current balancing. The current-sense gain is 10μA/A while the MOSFET is fully on. A resistor (RCS) on the CS pin generates VCS. ICS can be estimated with Equation (2): CS OUT I = I 10 A/A μ (2) VCS can be calculated with Equation (3): CS CS CS V = I R (3) Once VCS reaches VOCREF, the internal circuit regulates VGATE to maintain a constant IFET. Output Current Monitor (IMON) The MP5990 provides a high-accuracy MOSFET current monitor output (IMON). The current monitor gain is 10 μA/A. Connect a resistor (RIMON) between the IMON and GND pins. The recommended IMON voltage (VIMON) range is 0V to 1.6V, which is also within the internal ADC-sensing limit. IMON can be estimated with Equation (4): IMON OUT I = I 10 A/A μ (4) VIMON can be calculated with Equation (5): IMON IMON IMON V = I R (5) If there is no bandwidth requirement, place a 2.2nF to 100nF capacitor from IMON to GND to smooth the indicator voltage. |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |