AT45DB041D datasheet(7/53 Pages) ATMEL

7 / 53 page

3595H–DFLASH–03/07

AT45DB041D

memory is reached, the device will continue reading back at the beginning of the same page. A

low-to-high transition on the CS pin will terminate the read operation and tri-state the output pin

(SO). The maximum SCK frequency allowable for the Main Memory Page Read is defined by the

SCK specification. The Main Memory Page Read bypasses both data buffers and leaves the

contents of the buffers unchanged.

6.5

Buffer Read

The SRAM data buffers can be accessed independently from the main memory array, and utiliz-

ing the Buffer Read Command allows data to be sequentially read directly from the buffers. Four

opcodes, D4H or D1H for buffer 1 and D6H or D3H for buffer 2 can be used for the Buffer Read

Command. The use of each opcode depends on the maximum SCK frequency that will be used

to read data from the buffer. The D4H and D6H opcode can be used at any SCK frequency up to

the maximum specified by f

CAR1. The D1H and D3H opcode can be used for lower frequency

read operations up to the maximum specified by f

CAR2.

To perform a buffer read from the DataFlash standard buffer (264 bytes), the opcode must be

clocked into the device followed by three address bytes comprised of 15 don’t care bits and

9 buffer address bits (BFA8 - BFA0). To perform a buffer read from the binary buffer (256 bytes),

the opcode must be clocked into the device followed by three address bytes comprised of

16 don’t care bits and 8 buffer address bits (BFA7 - BFA0). Following the address bytes, one

don’t care byte must be clocked in to initialize the read operation. The CS pin must remain low

during the loading of the opcode, the address bytes, the don’t care bytes, and the reading of

data. When the end of a buffer is reached, the device will continue reading back at the beginning

of the buffer. A low-to-high transition on the CS pin will terminate the read operation and tri-state

the output pin (SO).

Program and Erase Commands

7.1

Buffer Write

Data can be clocked in from the input pin (SI) into either buffer 1 or buffer 2. To load data into the

DataFlash standard buffer (264 bytes), a 1-byte opcode, 84H for buffer 1 or 87H for buffer 2,

must be clocked into the device, followed by three address bytes comprised of 15 don’t care bits

and 9 buffer address bits (BFA8 - BFA0). The 9 buffer address bits specify the first byte in the

buffer to be written. To load data into the binary buffers (256 bytes each), a 1-byte opcode 84H

for buffer 1 or 87H for buffer 2, must be clocked into the device, followed by three address bytes

comprised of 16 don’t care bits and 8 buffer address bits (BFA7 - BFA0). The 8 buffer address

bits specify the first byte in the buffer to be written. After the last address byte has been clocked

into the device, data can then be clocked in on subsequent clock cycles. If the end of the data

buffer is reached, the device will wrap around back to the beginning of the buffer. Data will con-

tinue to be loaded into the buffer until a low-to-high transition is detected on the CS pin.

7.2

Buffer to Main Memory Page Program with Built-in Erase

Data written into either buffer 1 or buffer 2 can be programmed into the main memory. A 1-byte

opcode, 83H for buffer 1 or 86H for buffer 2, must be clocked into the device. For the DataFlash

standard page size (264 bytes), the opcode must be followed by three address bytes consist of

4 don’t care bits, 11 page address bits (PA10 - PA0) that specify the page in the main memory to

be written and 9 don’t care bits. To perform a buffer to main memory page program with built-in

erase for the binary page size (256 bytes), the opcode 83H for buffer 1 or 86H for buffer 2, must

be clocked into the device followed by three address bytes consisting of 5 don’t care bits

AT45DB041D датащи(PDF) 7 Page - ATMEL Corporation

AT45DB041D датащи(HTML) 7 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53

датащи скачать

ссылки URL