AD9983ASLASHPCB datasheet(37/44 Pages) AD

37 / 44 page

Preliminary Technical Data

AD9983A

Rev. PrA | Page 37 of 44

SYNC PROCESSING

0x20—Bit[2] PLL Sync Filter

This bit selects which signal the PLL uses. It can select between

either raw Hsync or SOG or filtered versions. The filtering of

the Hsync and SOG can eliminate nearly all extraneous

transitions, which have traditionally caused PLL disruption.

The power-up default setting is 0.

Table 60. PLL Sync Filter Enable

Select

Result

PLL uses raw Hsync or SOG inputs

PLL uses filtered Hsync or SOG inputs

0x20—Bit[1] Sync Processing Input Source

This bit selects whether the sync processor uses a raw sync or a

regenerated sync for the following functions: coast, H/V count,

field detection and Vsync duration counts. Using the

regenerated sync is recommended.

Table 61. SP Filter Enable

Select

Result

Sync processing uses raw Hsync or SOG

Sync processing uses the internally regenerated Hsync

0x21—Bits[7:0]

Must be set to default

0x22—Bits[7:0]

Must be set to default

0x23—Bits[7:0] Sync Filter Window Width

This 8-bit register sets the window of time for the regenerated

Hsync leading edge (in 25 ns steps) and that sync pulses are

allowed to pass through. Therefore with the default value of 10,

the window width is ±250 ns. The goal is to set the window

width so that extraneous pulses are rejected. (see the Sync

Processing section). As in the sync separator threshold, the

25 ns multiplier value is somewhat variable. The maximum

variability over all operating conditions is ±20% (20 ns to 30 ns).

DETECTION STATUS

0x24—Bit[7] HSYNC0 Detection Bit

This bit is used to indicate when activity is detected on the

HSYNC0 input pin. If Hsync is held high or low, activity is not

detected. The sync processing block diagram shows where this

function is implemented. 0 = HSYNC0 not active. 1 = HSYNC0

is active.

Table 62. HSYNC0 Detection Results

Detect

Result

No activity detected

Activity detected

0x24—Bit[6] HSYNC1 Detection Bit

This bit is used to indicate when activity is detected on the

HSYNC1 input pin. If Hsync is held high or low, activity is not

detected. The sync processing block diagram shows where this

function is implemented. 0 = HSYNC1 not active. 1 = HSYNC1

is active.

Table 63. HSYNC1 Detection Results

Detect

Result

No activity detected

Activity detected

0x24—Bit[5] VSYNC0 Detection Bit

This bit is used to indicate when activity is detected on the

VSYNC0 input pin. If Vsync is held high or low, activity is not

detected. The sync processing block diagram shows where this

function is implemented. 0 = VSYNC0 not active. 1 = VSYNC0

is active.

Table 64. VSYNC0 Detection Results

Detect

Result

No activity detected

Activity detected

0x24—Bit[4] VSYNC1 Detection Bit

This bit is used to indicate when activity is detected on the

VSYNC1 input pin. If Vsync is held high or low, activity is not

detected. The sync processing block diagram shows where this

function is implemented. 0 = VSYNC1 not active. 1 = VSYNC1

is active.

Table 65. VSYNC1 Detection Results

Detect

Result

No activity detected

Activity detected

0x24—Bit[3] SOGIN0 Detection Bit

This bit is used to indicate when activity is detected on the

SOGIN0 input pin. If SOG is held high or low, activity is not

detected. The sync processing block diagram shows where this

function is implemented. 0 = SOGIN0 not active. 1 = SOGIN0

is active.

Table 66. SOGIN0 Detection Results

Detect

Result

No activity detected

Activity detected

AD9983A/PCB датащи(PDF) 37 Page - Analog Devices

AD9983A/PCB датащи(HTML) 37 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44

датащи скачать

ссылки URL