ST72344 datasheet(133/191 Pages) STMICROELECTRONICS

133 / 191 page

ST72340, ST72344, ST72345

133/191

Notes:

– The Status Register has to be read to clear the

event flag associated with the interrupt

– An interrupt will be generated only if the interrupt

enable bit is set in the Control Register

– Slaves 1 and 2 have a common interrupt and the

Slave 3 has a separate interrupt.

– At the end of write operation, I2C3S is temporar-

ily disabled by hardware by setting BusyW bit in

CR2. The byte count register, status register and

current address register should be saved before

resetting BusyW bit.

11.7.5.1 Slave Reception (Write operations)

Byte Write: The Slave address is followed by an

8-bit byte address. Upon receipt of this address an

acknowledge is generated, address is moved into

the current address register and the 8 bit data is

clocked in. Once the data is shifted in, a DMA

request is generated and the data is written in the

RAM. The addressing device will terminate the

write sequence with a stop condition. Refer to

Figure 73

Page Write: A page write is initiated in similar way

to a byte write, but the addressing device does not

send a stop condition after the first data byte. The

page length is programmed using bits 7:6 (PL[1:0])

in the Control Register1.

The current address register value is incremented

by one every time a byte is written. When this

address reaches the page boundary, the next byte

will be written at the beginning of the same page.

Refer to Figure 74.

11.7.5.2 Slave Transmission (Read Operations)

Current Address Read: The current address

during the last read or write operation incremented

by one.

During this operation the I2C slave reads the data

pointed by the current address register. Refer to

Figure 75.

Random Read: Random read requires a dummy

byte write sequence to load in the byte address.

The addressing device then generates restart

condition and resends the device address similar

to current address read with the read/write bit high.

Refer to Figure 76. Some types of I2C masters

perform a dummy write with a stop condition and

then a current address read.

In either case, the slave generates a DMA request,

sends an acknowledge and serially clocks out the

data.

When the memory address limit is reached the

current address will roll over and the random read

will continue till the addressing master sends a

stop condition.

Sequential Read: Sequential reads are initiated

by either a current address read or a random

address

read.

After

the

addressing

master

receives the data byte it responds with an

acknowledge. As long as the slave receives an

acknowledge it will continue to increment the

current address register and clock out sequential

data bytes.

When the memory address limit is reached the

current address will roll over and the sequential

read will continue till the addressing master sends

a stop condition. Refer to Figure 78

11.7.5.3 Combined Format:

If a master wants to continue communication

either with another slave or by changing the

direction of transfer then the master would

generate a restart and provide a different slave

address or the same slave address with the R/W

bit reversed. Refer to Figure 79.

ST72344 датащи(PDF) 133 Page - STMicroelectronics

ST72344 датащи(HTML) 133 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL