ST72361 datasheet(152/224 Pages) STMICROELECTRONICS

152 / 224 page

ST72361

152/224

10.8 LINSCI SERIAL COMMUNICATION INTERFACE (LIN Master Only)

10.8.1 Introduction

The Serial Communications Interface (SCI) offers

a flexible means of full-duplex data exchange with

external equipment requiring an industry standard

NRZ asynchronous serial data format. The SCI of-

fers a very wide range of baud rates using two

baud rate generator systems.

10.8.2 Main Features

■ Full duplex, asynchronous communications

■ NRZ standard format (Mark/Space)

■ Dual baud rate generator systems

■ Independently

programmable

transmit

and

receive baud rates up to 500K baud.

■ Programmable data word length (8 or 9 bits)

■ Receive buffer full, Transmit buffer empty and

End of Transmission flags

■ 2 receiver wake-up modes:

– Address bit (MSB)

– Idle line

■ Muting function for multiprocessor configurations

■ Separate

enable bits for Transmitter and

Receiver

■ 4 error detection flags:

– Overrun error

– Noise error

– Frame error

– Parity error

■ 5 interrupt sources with flags:

– Transmit data register empty

– Transmission complete

– Receive data register full

– Idle line received

– Overrun error detected

■ Transmitter clock output

■ Parity control:

– Transmits parity bit

– Checks parity of received data byte

■ Reduced power consumption mode

■ LIN Synch Break send capability

10.8.3 General Description

The interface is externally connected to another

device by three pins (see Figure 1 on page 19).

Any SCI bidirectional communication requires a

minimum of two pins: Receive Data In (RDI) and

Transmit Data Out (TDO):

– SCLK: Transmitter clock output. This pin outputs

the transmitter data clock for synchronous trans-

mission (no clock pulses on start bit and stop bit,

and a software option to send a clock pulse on

the last data bit). This can be used to control pe-

ripherals that have shift registers (e.g. LCD driv-

ers). The clock phase and polarity are software

programmable.

– TDO: Transmit Data Output. When the transmit-

ter is disabled, the output pin returns to its I/O

port configuration. When the transmitter is ena-

bled and nothing is to be transmitted, the TDO

pin is at high level.

– RDI: Receive Data Input is the serial data input.

Oversampling techniques are used for data re-

covery by discriminating between valid incoming

data and noise.

Through these pins, serial data is transmitted and

received as frames comprising:

– An Idle Line prior to transmission or reception

– A start bit

– A data word (8 or 9 bits) least significant bit first

– A Stop bit indicating that the frame is complete.

This interface uses two types of baud rate generator:

– A conventional type for commonly-used baud

rates,

– An extended type with a prescaler offering a very

wide range of baud rates even with non-standard

oscillator frequencies.

ST72361 датащи(PDF) 152 Page - STMicroelectronics

ST72361 датащи(HTML) 152 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL