ST72361 datasheet(119/224 Pages) STMICROELECTRONICS

119 / 224 page

ST72361

119/224

SERIAL PERIPHERAL INTERFACE (Cont’d)

CONTROL/STATUS REGISTER (SPICSR)

Read/Write (some bits Read Only)

Reset Value: 0000 0000 (00h)

Bit 7 = SPIF Serial Peripheral Data Transfer Flag

(Read only)

This bit is set by hardware when a transfer has

been completed. An interrupt is generated if

SPIE = 1 in the SPICR register. It is cleared by

a software sequence (an access to the SPICSR

SPIDR register).

0: Data transfer is in progress or the flag has been

cleared.

1: Data transfer between the device and an exter-

nal device has been completed.

Note: While the SPIF bit is set, all writes to the

SPIDR register are inhibited until the SPICSR reg-

ister is read.

Bit 6 = WCOL Write Collision status (Read only)

This bit is set by hardware when a write to the

SPIDR register is done during a transmit se-

quence. It is cleared by a software sequence (see

Figure 6).

0: No write collision occurred

1: A write collision has been detected

Bit 5 = OVR SPI Overrun error (Read only)

This bit is set by hardware when the byte currently

being received in the shift register is ready to be

transferred into the SPIDR register while SPIF = 1

(See Section 0.1.5.2). An interrupt is generated if

SPIE = 1 in the SPICR register. The OVR bit is

cleared by software reading the SPICSR register.

0: No overrun error

1: Overrun error detected

Bit 4 = MODF Mode Fault flag (Read only)

This bit is set by hardware when the SS pin is

pulled low in master mode (see Section 0.1.5.1

Master Mode Fault (MODF)). An SPI interrupt can

be generated if SPIE = 1 in the SPICR register.

This bit is cleared by a software sequence (An ac-

cess to the SPICSR register while MODF = 1 fol-

lowed by a write to the SPICR register).

0: No master mode fault detected

1: A fault in master mode has been detected

Bit 3 = Reserved, must be kept cleared.

Bit 2 = SOD SPI Output Disable

This bit is set and cleared by software. When set, it

disables the alternate function of the SPI output

(MOSI in master mode / MISO in slave mode)

0: SPI output enabled (if SPE = 1)

1: SPI output disabled

Bit 1 = SSM SS Management

This bit is set and cleared by software. When set, it

disables the alternate function of the SPI SS pin

and uses the SSI bit value instead. See Section

0.1.3.2 Slave Select Management.

0: Hardware management (SS managed by exter-

nal pin)

1: Software management (internal SS signal con-

trolled by SSI bit. External SS pin free for gener-

al-purpose I/O)

Bit 0 = SSI SS Internal Mode

This bit is set and cleared by software. It acts as a

‘chip select’ by controlling the level of the SS slave

select signal when the SSM bit is set.

0: Slave selected

1: Slave deselected

DATA I/O REGISTER (SPIDR)

Read/Write

Reset Value: Undefined

The SPIDR register is used to transmit and receive

data on the serial bus. In a master device, a write

to this register will initiate transmission/reception

of another byte.

Notes: During the last clock cycle the SPIF bit is

set, a copy of the received data byte in the shift

the serial peripheral data I/O register, the buffer is

actually being read.

While the SPIF bit is set, all writes to the SPIDR

read.

Warning: A write to the SPIDR register places

data directly into the shift register for transmission.

A read to the SPIDR register returns the value lo-

cated in the buffer and not the content of the shift

SPIF

WCOL

OVR

MODF

SOD

SSM

SSI

ST72361 датащи(PDF) 119 Page - STMicroelectronics

ST72361 датащи(HTML) 119 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL