33975 datasheet(24/32 Pages) FREESCALE

24 / 32 page

Analog Integrated Circuit Device Data

Freescale Semiconductor

33975

TYPICAL APPLICATIONS

OPERATIONAL MODES

Figure 14. MOSFET or LED Driver Output

The sequence of commands (from Normal mode with

inputs tri-state) required to set up the device to drive a

MOSFET are as follows:

• wetting current timer enable command –Disable SPn

wetting current timer (refer to Table 9, page 16).

• metallic command –Set SPn to 16/32 mA or 2.0/4.0 mA

gate drive current (refer to Table 8, page 15).

• settings command –Set SPn as switch-to-battery (refer

to Table 6, page 14).

• tri-state command –Disable tri-state for SPn (refer to

Table 10, page 16).

After the tri-state command has been sent (tri-state

disable), the MOSFET gate will be pulled to ground. From this

point forward the MOSFET may be turned on and off by

sending the settings command:

• settings command –SPn as switch-to-ground

(MOSFET ON).

• settings command –SPn as switch-to-battery

(MOSFET OFF).

Monitoring of the MOSFET drain in the OFF state provides

open load detection. This is done by using an input

comparator. With the SGn input in tri-state, the load will pull

up the input to battery. With the load open, the SGn terminal

is pulled down to ground through an external resistor. The

open load is indicated by a logic [1] in the SO data bit.

The analog command may be used to monitor the drain

voltage in the MOSFET ON state. By sourcing 4.0 mA of

current to the 750 Ω resistor, the analog voltage on the SGn

terminal will be approximately:

As the voltage on the drain of the MOSFET increases, so

does the voltage on the SGn terminal. With the SGn terminal

selected as analog, the MCU may perform the A/D

conversion.

Using this method for controlling unclamped inductive

loads is not recommended. Inductive fly-back voltages

greater than VPWR may damage the IC.

The SP0–SP7 terminals of this device may also be used

to send signals from one module to another. Operation is

similar to the gate control of a MOSFET.

For LED applications a resistor in series with the LED is

recommended but not required. The switch-to-ground inputs

are recommended for LED application. To drive the LED use

the following commands:

• wetting current timer enable command –Disable SGn

wetting current timer.

• metallic command –Set SGn to 32 mA.

From this point forward the LED may be turned on and off

using the tri-state command:

• tri-state command –Disable tri-state for SGn (LED ON).

• tri-state command –Enable tri-state for SGn (LED

OFF).

These parameters are easily programmed via SPI

commands in Normal mode.

Multiple 33975 Devices in a Module System

Connecting power to the 33975 and the MCU for Sleep

mode operation may be done in several ways. Table 21

shows several system configurations for power between the

MCU and the 33975 and their specific requirements for

functionality.

SP0

SG0

SG13

4.0

4.0 V Ref

Comparator

To SPI

VPWR

SG0

750 Ω

VBAT

AMUX

100 kΩ

VPWR

Comparator

To SPI

4.0 V

Ref

4.0

2.0 mA

VPWR

SG0

4.0

VPWR

Comparator

To SPI

4.0 V Ref

SG13

Table 21. Sleep Mode Power Supply

MCU

VDD

33975

VDD

Comments

5.0 V

All wake-up conditions apply. (Refer to Sleep

Mode, page 20.)

5.0 V

SPI wake-up is not possible.

5.0 V

Sleep mode not possible. Current from CS pull

up will flow through MCU to VDD that has been

switched off. Negative edge of CS will put 33975

in Normal mode.

SPI wake-up is not possible.

VSGn = ISGn x 750Ω + VDS

33975 датащи(PDF) 24 Page - Freescale Semiconductor, Inc

33975 датащи(HTML) 24 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

датащи скачать

ссылки URL