CC2652PSIP datasheet(14/72 Pages) TI

14 / 72 page

Measured on the CC2652xSIP-EM reference design with Tc = 25 °C, VDDS = 3.0 V, fRF= 2440 MHz with

DC/DC enabled and high power PA connected to VDDS unless otherwise noted.

All measurements are performed at the antenna input with a combined RX and TX path, except for high power PA which is

measured at a dedicated antenna connection. All measurements are performed conducted.

PARAMETER

TEST CONDITIONS

MIN

TYP

MAX

UNIT

Selectivity, ±6 MHz(1)

Wanted signal at –72 dBm, modulated interferer at ≥ ±6

MHz, BER = 10–3

46 / 45(2)

Selectivity, ±7 MHz

Wanted signal at –72 dBm, modulated interferer at ≥ ±7

MHz, BER = 10–3

49 / 45(2)

Selectivity, Image frequency(1)

Wanted signal at –72 dBm, modulated interferer at image

frequency, BER = 10–3

Selectivity, Image frequency ±1

MHz(1)

Note that Image frequency + 1 MHz is the Co- channel

–1 MHz. Wanted signal at –72 dBm, modulated interferer

at ±1 MHz from image frequency, BER = 10–3

4 / 46(2)

1 Mbps (LE 1M)

Receiver sensitivity

Differential mode. BER = 10–3

–96

dBm

Receiver saturation

Differential mode. BER = 10–3

> 5

dBm

Frequency error tolerance

Difference between the incoming carrier frequency and

the internally generated carrier frequency

> (–350 / 350)

kHz

Data rate error tolerance

Difference between incoming data rate and the internally

generated data rate (37-byte packets)

> (–650 / 750)

ppm

Co-channel rejection(1)

Wanted signal at –67 dBm, modulated interferer in

channel, BER = 10–3

–6

Selectivity, ±1 MHz(1)

Wanted signal at –67 dBm, modulated interferer at ±1

MHz, BER = 10–3

7 / 4(2)

Selectivity, ±2 MHz(1)

Wanted signal at –67 dBm, modulated interferer at ±2

MHz,BER = 10–3

39 / 33(2)

Selectivity, ±3 MHz(1)

Wanted signal at –67 dBm, modulated interferer at ±3

MHz, BER = 10–3

36 / 40(2)

Selectivity, ±4 MHz(1)

Wanted signal at –67 dBm, modulated interferer at ±4

MHz, BER = 10–3

36 / 45(2)

Selectivity, ±5 MHz or more(1)

Wanted signal at –67 dBm, modulated interferer at ≥ ±5

MHz, BER = 10–3

Selectivity, image frequency(1)

Wanted signal at –67 dBm, modulated interferer at image

frequency, BER = 10–3

Selectivity, image frequency

±1 MHz(1)

Note that Image frequency + 1 MHz is the Co- channel

–1 MHz. Wanted signal at –67 dBm, modulated interferer

at ±1 MHz from image frequency, BER = 10–3

4 / 41(2)

Out-of-band blocking(3)

30 MHz to 2000 MHz

–10

dBm

Out-of-band blocking

2003 MHz to 2399 MHz

–18

dBm

Out-of-band blocking

2484 MHz to 2997 MHz

–12

dBm

Out-of-band blocking

3000 MHz to 12.75 GHz

–2

dBm

Intermodulation

Wanted signal at 2402 MHz, –64 dBm. Two interferers

at 2405 and 2408 MHz respectively, at the given power

level

–42

dBm

Spurious emissions,

30 to 1000 MHz(4)

Measurement in a 50-Ω single-ended load.

< –59

dBm

Spurious emissions,

1 to 12.75 GHz(4)

Measurement in a 50-Ω single-ended load.

< –47

dBm

RSSI dynamic range

RSSI accuracy

±4

2 Mbps (LE 2M)

Receiver sensitivity

Differential mode. Measured at SMA connector, BER =

10–3

–90

dBm

Receiver saturation

Differential mode. Measured at SMA connector, BER =

10–3

> 5

dBm

Frequency error tolerance

Difference between the incoming carrier frequency and

the internally generated carrier frequency

> (–500 / 500)

kHz

Data rate error tolerance

Difference between incoming data rate and the internally

generated data rate (37-byte packets)

> (–700 / 750)

ppm

CC2652PSIP

SWRS263A – FEBRUARY 2021 – REVISED JUNE 2022

www.ti.com

Submit Document Feedback

Product Folder Links: CC2652PSIP

CC2652PSIP датащи(PDF) 14 Page - Texas Instruments

CC2652PSIP датащи(HTML) 14 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72

датащи скачать

ссылки URL