PIC10F200 datasheet(69/86 Pages) MICROCHIP

69 / 86 page

Preliminary

DS41239B-page 67

PIC10F200/202/204/206

TABLE 12-1:

DC CHARACTERISTICS: PIC10F200/202/204/206 (Industrial, Extended)

DC CHARACTERISTICS

Standard Operating Conditions (unless otherwise specified)

Operating temperature

-40°C

≤ TA ≤ +85°C (industrial)

-40°C

≤ TA ≤ +125°C (extended)

Operating voltage VDD range as described in DC specification

Param

No.

Sym

Characteristic

Min

Typ†

Max

Units

Conditions

VIL

Input Low Voltage

I/O ports:

D030

with TTL buffer

Vss

—

0.8V

For all 4.5

≤ VDD ≤ 5.5V

D030A

Vss

—

0.15 VDD

Otherwise

D031

with

Schmitt

Trigger

buffer

Vss

—

0.15 VDD

D032

MCLR, T0CKI

Vss

—

0.15 VDD

VIH

Input High Voltage

I/O ports:

—

D040

with TTL buffer

2.0

—

VDD

V4.5

≤ VDD ≤ 5.5V

D040A

0.25 VDD

+ 0.8 VDD

—VDD

Otherwise

D041

with

Schmitt

Trigger

buffer

0.85 VDD

—VDD

For entire VDD range

D042

MCLR, T0CKI

0.85 VDD

—VDD

D070

IPUR

GPIO weak pull-up current(3)

TBD

250

TBD

μAVDD = 5V, VPIN = VSS

IIL

Input Leakage Current(1, 2)

D060

I/O ports

—

± 1

μA

Vss

≤ VPIN ≤ VDD, Pin at high-impedance

D061

GP3/MCLR(4)

——

± 30

μA

Vss

≤ VPIN ≤ VDD

D061A

GP3/MCLR(5)

——

± 5

μA

Vss

≤ VPIN ≤ VDD

Output Low Voltage

D080

I/O ports

—

0.6

IOL = 8.5 mA, VDD = 4.5V,

-40

°C to +85°C

D080A

—

0.6

IOL = 7.0 mA, VDD = 4.5V,

-40

°C to +125°C

Output High Voltage

D090

I/O ports(2)

VDD – 0.7

—

IOH = -3.0 mA, VDD = 4.5V,

-40

°C to +85°C

D090A

VDD – 0.7

—

IOH = -2.5 mA, VDD = 4.5V,

-40

°C to +125°C

Capacitive Loading Specs

on Output Pins

D101

All I/O pins

—

50*

Legend:

TBD = To Be Determined.

†

Data in “Typ” column is at 5V, 25

°C unless otherwise stated. These parameters are for design guidance only and are

not tested.

These parameters are for design guidance only and are not tested.

Note

The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent

normal operating conditions. Higher leakage current may be measured at different input voltages.

Negative current is defined as coming out of the pin.

Does not include GP3. For GP3 see parameters D061 and D061A.

This specification applies to GP3/MCLR configured as external MCLR and GP3/MCLR configured as input with internal

pull-up enabled.

This specification applies when GP3/MCLR is configured as an input with pull-up disabled. The leakage current of the

MCLR circuit is higher than the standard I/O logic.

PIC10F200 датащи(PDF) 69 Page - Microchip Technology

PIC10F200 датащи(HTML) 69 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86

датащи скачать

ссылки URL