| поискавой системы для электроныых деталей |
|
STPMIC1APQR датащи(PDF) 53 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
STPMIC1APQR датащи(HTML) 53 Page - STMicroelectronics |
|
53 / 140 page ![]() Table 11. Turn-on description Name Turn-ON condition source Configuration Active condition description Debounce Interrupt PONKEY PONKEYn pin N/A Active low 30 ms PKEY_RI/PKEY_FA in INT_PENDING_R1 VBUS (VBUSOTG) VBUSOTG pin Can be disable by settingVBUSOTG_DET_DIS bit in Table 48. BST_SW_CR VBUSOTG > VBUSOTG_Rise 30 ms VBUSOTG_RI/ VBUSOTG_FA in INT_PENDING_R1 VBUS (SWOUT) SWOUT pin Can be disable by setting SWOUT_DET_DIS bit in Table 30. SW_VIN_CR SWOUT > SWOUT_Rise 30 ms SWOUT_RI/ SWOUT_FA in INT_PENDING_R1 WAKEUP WAKEUP pin N/A Active high No debounce WKP_RI/WKP_FA in INT_PENDING_R1 The STPMIC1 manages 2 different scenarios depending if the turn-ON condition is active before or after VIN rises above VIN_POR_Rise. Active Turn-ON condition after VIN rises above VIN_POR_Rise sequence is presented in Figure 57. Turn-on condition after VIN_POR_RISE. Figure 57. Turn-on condition after VIN_POR_RISE t1: VIN rises above VIN_POR_Rise while no turn-ON condition is detected active. The STPMIC1 performs the PRELOAD_NVM and swiches to OFF-state. t2: the STPMIC1 starts detecting the activity on turn-ON condition but the detection threshold above is not stable. t3: turn-ON signal has been detected stable longer than debounce time. Turn-ON event triggered. Switch to CHECK&LOAD then POWER_UP as VIN > VINOK_Rise. t3 to t4: turn-ON conditions are ignored from CHECK&LOAD to POWER_ON. t4: turn-ON condition is ignored and does not affect the usual STPMIC1 behavior in POWER_ON. (Except PONKEY long key press. See Section 5.4.3 Turn-OFF conditions and restart_request). Active turn-ON signal does not prevent from POWER_DOWN. t5: active turn-OFF condition event occurs from a valid source. Switch to POWER_DOWN. t5 to t6: active turn-ON during POWER_DOWN is ignored. t7: New turn-ON signal rising edge has been detected after debounce time. A valid turn-ON condition is detected. The STPMIC1 switches to POWER_UP. STPMIC1 Feature description DS12792 - Rev 7 page 53/140 |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |