AGLP060 datasheet(76/128 Pages) ACTEL

76 / 128 page

IGLOO PLUS DC and Switching Characteristics

2- 62

R e v i sio n 1 1

Table 2-91 • IGLOO PLUS CCC/PLL Specification

For IGLOO PLUS V2 Devices, 1.2 V DC Core Supply Voltage

Parameter

Min.

Typ.

Max.

Units

Clock Conditioning Circuitry Input Frequency fIN_CCC

1.5

160

MHz

Clock Conditioning Circuitry Output Frequency fOUT_CCC

0.75

160

MHz

Delay Increments in Programmable Delay Blocks 1, 2

580

Number of Programmable Values in Each Programmable Delay Block

Serial Clock (SCLK) for Dynamic PLL3,4

Input Cycle-to-Cycle Jitter (peak magnitude)

MHz

Acquisition Time

LockControl = 0

300

µs

LockControl = 1

6.0

Tracking Jitter5

LockControl = 0

LockControl = 1

Output Duty Cycle

48.5

51.5

Delay Range in Block: Programmable Delay 1 1, 2

2.3

20.86

Delay Range in Block: Programmable Delay 2 1, 2

0.025

20.86

Delay Range in Block: Fixed Delay 1, 2

5.7

VCO Output Peak-to-Peak Period Jitter FCCC_OUT

Maximum Peak-to-Peak Period Jitter6,7,8

SSO

≤ 2

SSO

≤ 4

SSO

≤ 8 SSO ≤ 16

0.75 MHz to 50 MHz

0.50%

1.20%

2.00%

3.00%

50 MHz to 160 MHz

2.50%

5.00%

7.00%

15.00%

Notes:

1. This delay is a function of voltage and temperature. See Table 2-6 on page 2-6 and Table 2-7 on page 2-7 for deratings.

2. TJ = 25°C, VCC = 1.2 V

3. Maximum value obtained for a STD speed grade device in Worst Case Commercial Conditions.For specific junction

temperature and voltage supply levels, refer to Table 2-6 on page 2-6 and Table 2-7 on page 2-7 for derating values.

4. The AGLP030 device does not support PLL.

5. Tracking jitter is defined as the variation in clock edge position of PLL outputs with reference to PLL input clock edge.

Tracking jitter does not measure the variation in PLL output period, which is covered by period jitter parameter.

6. VCO output jitter is calculated as a percentage of the VCO frequency. The jitter (in ps) can be calculated by multiplying

the VCO period by the per cent jitter. The VCO jitter (in ps) applies to CCC_OUT regardless of the output divider

settings. For example, if the jitter on VCO is 300 ps, the jitter on CCC_OUT is also 300 ps, regardless of the output

divider settings.

7. Measurements are done with LVTTL 3.3 V, 8 mA, I/O drive strength and high slew rate. VCC/VCCPLL = 1.14 V,

VCCI = 3.3 V, VQ/PQ/TQ type of packages, 20 pF load.

8. SSO are outputs that are synchronous to a single clock domain, and have their clock-to-out times within ±200 ps of each

other. Switching I/Os are placed outside of the PLL bank. Refer to the "ProASIC3/E SSO and Pin Placement Guidelines"

chapter of the ProASIC3 FPGA Fabric User’s Guide.

AGLP060 датащи(PDF) 76 Page - Actel Corporation

AGLP060 датащи(HTML) 76 Page - Actel Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL