USB334X datasheet(60/92 Pages) MICROCHIP

60 / 92 page

USB334x

DS00002646A-page 60

 2009-2018 Microchip Technology Inc.

In Carkit Mode, interrupts are possible if they have been enabled in the Carkit Interrupt Enable register. The state of

each interrupt source is sampled prior to the assertion of DIR and this is compared against the asynchronous level from

interrupt source. In Carkit Mode, the Linestate signals are not available per the ULPI specification.

The ULPI interface is redefined to the following when Carkit Mode is entered.

Exiting Carkit Mode is the same as exiting Low Power Mode as described in Section 6.5.2, "Exiting Low Power Mode,"

on page 57. The Link must assert STP to signal the PHY to exit serial mode. When the PHY can accept a command,

DIR is de-asserted and the PHY will wait until the Link de-asserts STP to resume synchronous ULPI operation. The

RESETB pin can also be pulsed low to reset the USB334x and return it to Synchronous Mode.

6.7.1

ENTERING USB UART MODE

The USB334x can be placed into UART Mode by first setting the TxdEn and RxdEn bits in the Carkit Control register.

Then the Link can set the CarkitMode bit in the Interface Control register. The TxdEn and RxdEn bits must be written

before the CarkitMode bit.

After the CarkitMode bit is set, the ULPI interface will become redefined as described in Table 6-10, and the USB334x

will transmit data through the DATA[0] to DM of the USB connector and receive data on DP and pass the information

the Link on DATA[1].

When entering UART mode, the regulator output will automatically switch to the value configured by the UART RegOut-

put bits in the USB IO & Power Management register and the RCD pull-up resistors will be applied internally to DP and

DM. This will hold the UART in its default operating state.

While in UART mode, the transmit edge rates can be set to either the Full Speed USB or Low Speed USB edge rates

by using the XcvrSelect[1:0] bits in the Function Control register.

TABLE 6-10:

PIN DEFINITIONS IN CARKIT MODE

Signal

Connected to

Direction

Description

txd

DATA[0]

UART TXD signal that is routed to the DM pin if the TxdEn

is set in the Carkit Control register.

rxd

DATA[1]

OUT

UART RXD signal that is routed to the DP pin if the RxdEn

bit is set in the Carkit Control register.

reserved

DATA[2]

OUT

Driven Low (CarkitDataMC = 0, default)

Tri-state (CarkitDataMC = 1)

int

DATA[3]

OUT

Asserted when any unmasked interrupt occurs. Active high.

reserved

DATA[4:7]

OUT

Driven Low.

TABLE 6-11:

ULPI REGISTER PROGRAMMING EXAMPLE TO ENTER UART MODE

R/W

Address

(HEX)

Value

(HEX)

Description

Result

Configure Non-Driving mode

Select FS transmit edge rates

OpMode=01

XcvrSelect=01

Set regulator to 3.3V

UART RegOutput=00

Enable UART connections

RxdEn=1

TxdEn=1

Enable carkit mode

CarkitMode=1

USB334X датащи(PDF) 60 Page - Microchip Technology

USB334X датащи(HTML) 60 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92

датащи скачать

ссылки URL