 |
поискавой системы для электроныых деталей |
|
|
поискавой системы для электроныых деталей |
|
PIC12F635E/SS датащи(PDF) 152 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
PIC12F635E/SS датащи(HTML) 152 Page - Microchip Technology |
|
|
152 / 196 page  PIC12F635/PIC16F636/639 DS41232B-page 150 Preliminary © 2005 Microchip Technology Inc. 15.2 DC Characteristics: PIC12F635/PIC16F636-I (Industrial) DC CHARACTERISTICS Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C ≤ TA ≤ +85°C for industrial Param No. Sym Device Characteristics Min Typ† Max Units Conditions VDD Note D010 IDD Supply Current(1,2) —9 TBD μA2.0 FOSC = 32.768 kHz LP Oscillator mode —18 TBD μA3.0 —35 TBD μA5.0 D011 — 110 TBD μA2.0 FOSC = 1 MHz XT Oscillator mode —190 TBD μA3.0 —330 TBD μA5.0 D012 — 220 TBD μA2.0 FOSC = 4 MHz XT Oscillator mode —370 TBD μA3.0 —600 TBD μA5.0 D013 — 70 TBD μA2.0 FOSC = 1 MHz EC Oscillator mode —140 TBD μA3.0 —260 TBD μA5.0 D014 — 180 TBD μA2.0 FOSC = 4 MHz EC Oscillator mode —320 TBD μA3.0 —580 TBD μA5.0 D015 — TBD TBD μA2.0 FOSC = 31 kHz LFINTOSC mode —TBD TBD μA3.0 —TBD TBD mA 5.0 D016 — 340 TBD μA2.0 FOSC = 4 MHz HFINTOSC mode —500 TBD μA3.0 —800 TBD μA5.0 D017 — 180 TBD μA2.0 FOSC = 4 MHz EXTRC mode —320 TBD μA3.0 —580 TBD μA5.0 D018 — 2.1 TBD mA 4.5 FOSC = 20 MHz HS Oscillator mode — 2.4 TBD mA 5.0 Legend: TBD = To Be Determined † Data in ‘Typ’ column is at 5.0V, 25 °C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: The test conditions for all IDD measurements in Active Operation mode are: OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD; MCLR = VDD; WDT disabled. MCU only, Analog Front-End not included. 2: The supply current is mainly a function of the operating voltage and frequency. Other factors, such as I/O pin loading and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact on the current consumption. MCU only, Analog Front-End not included. 3: The peripheral current is the sum of the base IDD or IPD and the additional current consumed when this peripheral is enabled. The peripheral Δ current can be determined by subtracting the base IDD or IPD current from this limit. Max values should be used when calculating total current consumption. 4: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD. |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Russian ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
