OL2385SWUG datasheet(32/64 Pages) NXP

32 / 64 page

NXP Semiconductors

OL2385SWUG

SIGFOX software driver

OL2385SWUG

All information provided in this document is subject to legal disclaimers.

User guide

Rev. 2.1 — 6 April 2018

32 / 64

When the SIGFOX software driver is configured properly, the user can take advantage

of all of the prepared functions to construct the application. See the API Programmer's

Guide, included in the SIGFOX software driver zip file, for function signatures and

required parameters. Also, review the sf/sf.h header file, which contains prototypes for all

available functions.

For more complex driver use cases, refer to the included example projects.

6.2.5.9 Compiling, downloading and debugging

To compile a project, click the compile icon in the toolbar.

The process for downloading an application onto an MCU board in Kinetis Design Studio

differs according to the type of board. For more information, see the Kinetis Design

Studio V3.2.0-User's Guide. To download and debug on the KL43Z MCU board, do the

following:

1. Click the arrow next to the debug icon in the toolbar and select

Debug

Configurations…

2. In the

Debug Configurations dialog box, click KL43_SDK_Project_Debug_PNE

under

GDB PEMicro Interface Debugging.

3. Click the

Debugger tab and set the Interface option to OpenSDA Embedded Debug –

USB Port. Then click the

Refresh button next to the Port setting to update the list of

available USB ports.

4. Then make sure that the Target is set to KL43Z256M4. If not, click on the

Select

Device button. In the Select Target Device dialog box go to NXP → KL4x →

KL43Z256M4. Confirm the selection by clicking the Select button.

5. Click

Debug. Kinetis Design Studio will download and launch the program on board.

7 Testing the SIGFOX application

7.1 Testing on SIGFOX Base Station

SIGFOX backend can be used for a basic functionality check of the SIGFOX module.

This includes reception of a SIGFOX message and display of its payload along with

repetition number. The base station can be leased from SIGFOX or generally is deployed

by SIGFOX in your city. Visit www.SIGFOX.com/en/coverage to check coverage in your

city. The base station is connected to the cloud by the internet; and it can receive a

SIGFOX message sent by an OL2385 board and display it on a web browser.

7.1.1 Registering SIGFOX device on network

1. Take a note of the Device ID and PAC of the device. If the device is preflashed, these

numbers are already flashed inside. If you have SPI based firmware on OL2385

(check the section Section 5.4.1 "Setting up KL43Z board with terminal program"),

you can get the Device ID and PAC using the SPI command Get info. For UART

based firmware, send the command AT$ID? via an FTDI cable. If the device is not

preflashed, contact NXP customer support.

2. Activate your device by registering it on backend.SIGFOX.com/activate.

3. Choose your kit provider from the list as shown in the figure below.

4. Fill in the subscription information as shown below and click Subscribe.

5. Check your email for a message regarding your account.

OL2385SWUG датащи(PDF) 32 Page - NXP Semiconductors

OL2385SWUG датащи(HTML) 32 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64

датащи скачать

ссылки URL