PIC16F505 datasheet(75/98 Pages) MICROCHIP

75 / 98 page

 2004 Microchip Technology Inc.

Preliminary

DS41236A-page 73

PIC12F508/509/16F505

TABLE 10-1:

DC CHARACTERISTICS: PIC12F508/509/16F505 (Industrial, Extended)

DC CHARACTERISTICS

Standard Operating Conditions (unless otherwise specified)

Operating temperature

-40°C

≤ TA ≤ +85°C (industrial)

-40°C

≤ TA ≤ +125°C (extended)

Operating voltage VDD range as described in DC specification

Param

No.

Sym

Characteristic

Min

Typ†

Max

Units

Conditions

VIL

Input Low Voltage

I/O ports:

D030

with TTL buffer

Vss

—

0.8V

For all 4.5

≤ VDD ≤ 5.5V

D030A

Vss

—

0.15 VDD

Otherwise

D031

with Schmitt Trigger buffer

Vss

—

0.15 VDD

D032

MCLR, T0CKI

Vss

—

0.15 VDD

D033

OSC1 (in EXTRC)

Vss

—

0.15 VDD

(Note1)

D033

OSC1 (in HS)

Vss

—

0.3 VDD

(Note1)

D033

OSC1 (in XT and LP)

Vss

—

0.3

(Note1)

VIH

Input High Voltage

I/O ports:

—

D040

with TTL buffer

2.0

—

VDD

V4.5

≤ VDD ≤ 5.5V

D040A

0.25 VDD

+ 0.8 VDD

—VDD

Otherwise

D041

with Schmitt Trigger buffer

0.85 VDD

—VDD

For entire VDD range

D042

MCLR, T0CKI

0.85 VDD

—VDD

D043

OSC1 (in EXTRC)

0.85 VDD

—VDD

(Note1)

D043

OSC1 (in HS)

0.7 VDD

—VDD

(Note1)

D043

OSC1 (in XT and LP)

1.6

—

VDD

D070

IPUR

GPIO weak pull-up current(4)

TBD

250

TBD

µAVDD = 5V, VPIN = VSS

IIL

Input Leakage Current(2), (3)

D060

I/O ports

—

± 1

µAVss ≤ VPIN ≤ VDD, Pin at high-impedance

D061

GP3/RB3/MCLRI(5)

——

± 30

µAVss ≤ VPIN ≤ VDD

D061A

GP3/RB3/MCLRI(6)

——

± 5

µAVss ≤ VPIN ≤ VDD

D063

OSC1

—

± 5

µAVss ≤ VPIN ≤ VDD, XT, HS and LP oscillator

configuration

Output Low Voltage

D080

I/O ports/CLKOUT

—

0.6

IOL = 8.5 mA, VDD = 4.5V, -40

°C to +85°C

D080A

—

0.6

IOL = 7.0 mA, VDD = 4.5V, -40

°C to +125°C

D083

OSC2

—

0.6

IOL = 1.6 mA, VDD = 4.5V, -40

°C to +85°C

D083A

—

0.6

IOL = 1.2 mA, VDD = 4.5V, -40

°C to +125°C

Output High Voltage

D090

I/O ports/CLKOUT(3)

VDD – 0.7

—

IOH = -3.0 mA, VDD = 4.5V, -40

°C to +85°C

D090A

VDD – 0.7

—

IOH = -2.5 mA, VDD = 4.5V, -40

°C to +125°C

D092

OSC2

VDD – 0.7

—

IOH = -1.3 mA, VDD = 4.5V, -40

°C to +85°C

D092A

VDD – 0.7

—

IOH = -1.0 mA, VDD = 4.5V, -40

°C to +125°C

Capacitive Loading Specs on

Output Pins

D100

OSC2 pin

—

In XT, HS and LP modes when external clock is

used to drive OSC1.

D101

All I/O pins and OSC2

—

Legend:

TBD = To Be Determined.

†

Data in “Typ” column is at 5V, 25

°C unless otherwise stated. These parameters are for design guidance only and are not tested.

Note

In EXTRC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PIC12F508/509/

16F505 be driven with external clock in RC mode.

The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent normal operating

conditions. Higher leakage current may be measured at different input voltages.

Negative current is defined as coming out of the pin.

Does not include GP3/RB3. For GP3/RB3 see parameters D061 and D061A.

This specification applies to GP3/RB3/MCLR configured as external MCLR and GP3/RB3/MCLR configured as input with internal pull-up

enabled.

This specification applies when GP3/RB3/MCLR is configured as an input with pull-up disabled. The leakage current of the MCLR circuit

is higher than the standard I/O logic.

PIC16F505 датащи(PDF) 75 Page - Microchip Technology

PIC16F505 датащи(HTML) 75 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98

датащи скачать

ссылки URL