| поискавой системы для электроныых деталей |
|
MCP6S21 датащи(PDF) 19 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
MCP6S21 датащи(HTML) 19 Page - Microchip Technology |
|
19 / 43 page ![]() 2003 Microchip Technology Inc. DS21117A-page 19 MCP6S21/2/6/8 5.2 Registers The analog functions are programmed through the SPI interface using 16-bit words (see Figure 5-1 and Figure 5-2). This data is sent to two of three 8-bit regis- ters: Instruction Register (Register 5-1), Gain Register (Register 5-2) and Channel Register (Register 5-3). The power-up defaults for these three registers are: • Instruction Register: 000x xxx0 • Gain Register: xxxx x000 • Channel Register: xxxx x000 Thus, these devices are initially programmed with the Instruction Register set for NOP (no operation), a gain of +1 V/V and CH0 as the input channel. 5.2.1 INSTRUCTION REGISTER The Instruction Register has 3 command bits and 1 indirect address bit; see Register 5-1. The command bits include a NOP (000) to support daisy chaining (see Section 5.3, “Registers”); the other NOP commands shown should not be used (they are reserved for future use). The device is brought out of Shutdown mode when a valid command, other than NOP or Shutdown, is sent and CS is raised. REGISTER 5-1: INSTRUCTION REGISTER W-0 W-0 W-0 U-x U-x U-x U-x W-0 M2 M1 M0 — — — —A0 bit 7 bit 0 bit 7-5 M2-M0: Command Bits 000 = NOP (Default) (Note 1) 001 = PGA enters Shutdown Mode as soon as a full 16-bit word is sent and CS is raised. (Notes 1 and 2) 010 = Write to register. 011 = NOP (reserved for future use) (Note 1) 1XX = NOP (reserved for future use) (Note 1) bit 4-1 Unimplemented: Read as ‘0’ (reserved for future use) bit 0 A0: Indirect Address Bit 1 = Addresses the Channel Register 0 = Addresses the Gain Register (Default) Note 1: All other bits in the 16-bit word (including A0) are “don’t cares”. 2: The device exits Shutdown mode when a valid command (other than NOP or Shut- down) is sent and CS is raised; that valid command will be executed. Shutdown does not toggle. Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ’1’ = Bit is set ’0’ = Bit is cleared x = Bit is unknown |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |