SN74AHCT574DBLE datasheet(2/2 Pages) TI

2 / 2 page

SN54AHCT574, SN74AHCT574

OCTAL EDGE-TRIGGERED D-TYPE FLIP-FLOPS

WITH 3-STATE OUTPUTS

SCLS245L – OCTOBER 1995 – REVISED JULY 2003

POST OFFICE BOX 655303

• DALLAS, TEXAS 75265

description/ordering information (continued)

OE does not affect internal operations of the flip-flop. Old data can be retained or new data can be entered while

the outputs are in the high-impedance state.

To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup

resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.

FUNCTION TABLE

(each flip-flop)

INPUTS

OUTPUT

CLK

↑

H or L

logic diagram (positive logic)

CLK

To Seven Other Channels

absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†

Supply voltage range, VCC

–0.5 V to 7 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Input voltage range, VI (see Note 1)

–0.5 V to 7 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Output voltage range, VO (see Note 1)

–0.5 V to VCC + 0.5 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Input clamp current, IIK (VI < 0)

–20 mA

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Output clamp current, IOK (VO < 0 or VO > VCC)

±20 mA

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Continuous output current, IO (VO = 0 to VCC)

±25 mA

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Continuous current through VCC or GND

±75 mA

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Package thermal impedance,

θJA (see Note 2): DB package

°C/W

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

DGV package

°C/W

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

DW package

°C/W

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

N package

°C/W

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

NS package

°C/W

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

PW package

°C/W

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Storage temperature range, Tstg

–65

°C to 150°C

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and

functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not

implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

NOTES:

1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed.

2. The package thermal impedance is calculated in accordance with JESD 51-7.

SN74AHCT574DBLE датащи(PDF) 2 Page - Texas Instruments

SN74AHCT574DBLE датащи(HTML) 2 Page - Texas Instruments

Html Pages

1 2

датащи скачать

ссылки URL