PI5C3306 datasheet(2/3 Pages) PERICOM

2 / 3 page

PS8144C

01/11/01

12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012

PI5C3306

2-Bit Bus Switch with Active Low Enables

Capacitance (TA = 25°C, f = 1 MHz)

Parameters(4)

Description

Test Conditions

Typ

Units

CIN

Input Capacitance

VIN =0V

COFF

A/B Capacitance, Switch Off

VIN =0V

CON

A/B Capacitance, Switch On

VIN = 0V

Parameters

Description

Test Conditions(1)

Min.

Typ(2)

Max.

Units

VIH

Input HIGH Voltage

Guaranteed Logic HIGH Level

2.0

VIL

Input LOW Voltage

Guaranteed Logic LOW Level

–0.5

0.8

IIH

Input HIGH Current

VCC = Max., VIN = VCC

±1

µA

IIL

Input LOW Current

VCC = Max., VIN = GND

±1

µA

IOZH

High Impedance Output Current

≤A, B ≤VCC

±1

µA

IOZL

Low Impedance Output Current

≤A, B ≤VCC

±1

Input Hysteresis at Control Pins

300

RON

Switch On Resistance(3)

VCC =4.5V,VIN =0.0V,ION =30mAor64mA

Ω

VCC=4.5V,VIN=2.4V,ION=15mA

Storage Temperature .......................................................... –65°C to +150°C

Ambient Temperature with Power Applied ..........................–40°C to +85°C

Supply Voltage to Ground Potential (Inputs & Vcc Only) .... –0.5V to +7.0V

Supply Voltage to Ground Potential (Outputs & D/O Only) . –0.5V to +7.0V

DC Input Voltage ................................................................... –0.5V to +7.0V

DC Output Current ............................................................................ 120mA

Power Dissipation ................................................................................. 0.5W

Note:

Stresses greater than those listed under MAXIMUM

RATINGS may cause permanent damage to the

device. This is a stress rating only and functional

operation of the device at these or any other condi-

tions above those indicated in the operational sec-

tions of this specification is not implied. Exposure to

absolute maximum rating conditions for extended

periods may affect reliability.

Notes:

1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.

2. Typical values are at VCC = 5.0V, TA = 25°C ambient and maximum loading.

3. Measured by the voltage drop between A and B pin at indicated current through the switch. ON resistance is determined

by the lower of the voltages on the two (A, B) pins.

4. This parameter is determined by device characterization but is not production tested.

Power Supply Characteristics

Parameters Description

Test Conditions

(1)

Min.

Typ

(2)

Max.

Units

ICC

Quiescent Power Supply Current

VCC =Max.

VIN = GND or VCC

0.1

3.0

µA

∆ICC

Supply Current per Input @ TTL HIGH

VCC =Max.

VIN =3.4V

(3)

2.5

Notes:

1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device.

2. Typical values are at VCC = 5.0V, +25°C ambient.

3. Per TTL driven input (VIN = 3.4V, control inputs only); A and B pins do not contribute to ICC.

Maximum Ratings

(Above which the useful life may be impaired. For user guidelines, not tested.)

DC Electrical Characteristics (Over the Operating Range, TA = –40°C to +85°C, VCC = 4V to 5.5V)

PI5C3306 датащи(PDF) 2 Page - Pericom Semiconductor Corporation

PI5C3306 датащи(HTML) 2 Page - Pericom Semiconductor Corporation

Html Pages

1 2 3

датащи скачать

ссылки URL