TPS79718

TPS79730

TPS79733

SLVS332B – MARCH 2001 – REVISED JUNE 2001

3

www.ti.com

electrical characteristics over recommended operating free-air temperature range,

PARAMETER

TEST CONDITIONS

MIN

TYP

MAX

UNIT

V

Input voltage (see Note 2)

IO = 3 mA

1.8

5.5

V

VI

Input voltage (see Note 2)

IO = 10 mA

2

5.5

V

IO

Continuous output current (see Note 3)

0

10

mA

TJ

Operating junction temperature, TJ

-40

85

°C

TPS79718

TA = 25°C,

2.8 V < VI < 5.5 V

1.8

V

TPS79718

TA = –40°C to 85°C,

2.8 V < VI < 5.5 V

1.728

1.872

V

Output voltage (10

µA to 10 mA Load)

TPS79730

TA = 25°C,

4 V < VI < 5.5 V

3.0

V

Out ut voltage (10

µA to 10 mA Load)

(see Note 4)

TPS79730

TA = –40°C to 85°C,

4 V < VI < 5.5 V

2.880

3.120

V

TPS79733

TA = 25°C,

4.3 V < VI < 5.5 V

3.3

V

TPS79733

TA = –40°C to 85°C,

4.3 V < VI < 5.5 V

3.168

3.432

V

Quiescent current (GND current) (see Note 4)

TA = 25°C,

0

µA < IO < 10 mA

1.2

A

Quiescent current (GND current) (see Note 4)

TA = –40°C to 85°C,

IO = 10 mA

2

µA

Load regulation

TA = 25°C,

IO = 1 µA to 10 mA

17

mV

Output voltage line regulation (

∆V/V

(see Note 4)

VO + 1 V < VI ≤ 5.5 V, TA = 25°C

0.15

%/V

Output voltage line regulation (

VO + 1 V < VI ≤ 5.5 V, TA = –40°C to 85°C

0.8

%/V

Output noise voltage (TPS79718)

BW = 200 Hz to 100 kHz, Co = 10 µF,

IO = 10 mA,

TA = 25°C

600

µVRMS

Output current limit

VO = 0 V,

See Note 4

190

300

mA

Power supply ripple rejection (TPS79718)

f = 100 Hz,

Co = 10 µF,

IO = 10 mA,

TA = 25°C

50

dB

TPS79730

IO = 10 mA,

TA = 25°C

110

Dropout voltage (see Note 5)

TPS79730

IO = 10 mA,

TA = –40°C to 85°C

200

mV

Dropout voltage (see Note 5)

TPS79733

IO = 10 mA,

TA = 25°C

105

mV

TPS79733

IO = 10 mA,

TA = –40°C to 85°C

200

Minimum input voltage for valid PG

IO(PG) = 100µA,

V(PG) ≥ 0.8 V

1.2

V

PG trip threshold voltage

VO decreasing

82

90

96

%VO

PG output low voltage

VI = 1.5 V,

IO(PG) = 1 mA

0.14

0.225

V

PG leakage current

V(PG) = 5 V

0.1

nA

NOTES:

2. To calculate the minimum input voltage for your maximum output current, use the following formula:

VI(min) = VO(max) + VDO (max load)

3. Continuous output current is limited by internal protection circuitry, but it is not recommended that the device operate under

conditions beyond those specified in this table for extended periods of time.

4. The minimum IN operating voltage is 1.8 V or VO (typ) + 1 V, whichever is greater. The maximum IN voltage is 5.5 V. There is no

minimum output current requirement and the maximum output current is 10 mA.

5. IN voltage equals VO(typ) –100 mV; The TPS79730 input voltage is set to 2.9 V and the TPS79733 input voltage is set to 3.2 V. The

TPS79718 dropout voltage is limited by input voltage range limitations.