| поискавой системы для электроныых деталей |
|
ZSSC3036 датащи(PDF) 13 Page - Integrated Device Technology |
|
|
|||||||||||||||||||||||||||||
ZSSC3036 датащи(HTML) 13 Page - Integrated Device Technology |
|
13 / 48 page ![]() ZSSC3036 Datasheet © 2016 Integrated Device Technology, Inc. 13 April 20, 2016 3) Determine which of the two following cases is valid. a. If RatioOffset – A2D_offset ≤ 0 then calculate Theoretical optimum gain: Gainopt =(1 – A2D_offset) * Vref / Vmax b. If RatioOffset – A2D_offset > 0 then calculate Theoretical optimum gain: Gainopt = A2D_offset * Vref / |Vmin| with: Vref = Vrefp – Vrefn = 0.94·VDDB,min ≈ 1.5V Finally, select the setup gain (Gainsetup) as the nearest gain to Gainopt, where Gainsetup ≤ Gain opt. 2.3.2. Analog-to-Digital Converter A second-order charge-balancing analog-to-digital converter (ADC) is used to convert the amplifier signal. To allow optimizing the trade-off between conversion time and resolution, the conversion is split into a MSB coarse conversion and an LSB fine conversion. The final ADC resolution is determined by MSB + LSB. For the bridge measurement, the MSB-LSB segmentation is programmable via the Msb and Lsb settings in the BM_config register (10HEX; see section 3.6.3) stored in the MTP memory (see section 2.4.2). For the temperature measurement, the MSB-LSB segmentation is programmable via the Temp_ADC settings in the BM_config register. The conversion time is proportional to 2 MSB +2LSB. During the MSB coarse conversion, the ADC input signal is sampled and integrated 2 MSB times, resulting in inherit low-pass behavior and noise suppression. The longer the MSB coarse conversion is, the better the noise suppression is. Possible settings are listed below in Table 2.4 and Table 2.5. Table 2.4 MSB/LSB Segmentation Settings for Bridge Measurement Msb Setup Bits [7:6] in BM_config Number of MSB Coarse Conversion Bits Lsb Setup Bits [9:8] in BM_config Number of LSB Fine Conversion Bits 00BIN 10 00BIN 0 01BIN 12 01BIN 2 10BIN 14 10BIN 4 11BIN 16 11BIN 6 Table 2.5 MSB/LSB Segmentation Settings for Temperature Measurement Temp_ADC Setup Bits [14:13] in BM_config Number of MSB Coarse Conversion Bits Number of LSB Fine Conversion Bits 00BIN Setup according to IDT configuration in reserved memory (recommended setup for best performance and speed trade-off) 01BIN 16 0 10BIN 10 6 11BIN 12 4 |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |