12

DF22 Series

Molded-in lance

Flat-bladed screwdriver

(1)

(2)

2-6-3,Nakagawa Chuoh,Tsuzuki-Ku,Yokohama-Shi 224-8540,JAPAN

TEL: +81-45-620-3526 Fax: +81-45-591-3726

http://www.hirose.com

http://www.hirose-connectors.com

®

BTools

BContact Extraction

■ Contact extraction tool : Flat-bladed screwdriver, 1.4mm blade width

■ Intended crimp Contacts : DF22-1416SC(F), DF22-1416SCFA, DF22A-1416SC(F),

DF22A-1416SCFA, DF22A-1012SC(F), DF22A-1012SCFA,

DF22-1416PC(F), DF22-1416PCFA, and DF22A-1416PC(F)

■ Work Method

Housing Cross-

Sectional Diagram

BPrecautions

●The connector could be damaged if it is pulled out forcibly. When it is hard to pull out, push it in slightly first and then

depress the lock and un- mate.

●When thick, short sections of wire are used, the connector could be deformed due to the force of the wires’ position.

Route cables in such a way that they do twist when being installed.

●Incomplete insertion of the contact can be prevented by mounting a retainer; however, mounting of a retainer might not

be possible when the contact protrudes beyond the socket. Insert the contact securely and then mount the retainer.

●Please refer to the documents "Cable assembly Procedure", "Crimp condition" and "Crimp quality standards" for

the cable assembly procedures.

●Please refer to the "Mating/Unmating Operation Instruction Manual" for the connector operation.

●Please refer to the "Nylon Connector Guide" for handling instructions.

1. Refer to the drawing No. 1. Insert

correct size screwdriver in the

insulator against the molded-in

lance. Deflect the lance as shown.

2. Assure that the lance is deflected

to release the contact and pull- out

wire with the terminated contact.

Note 1 : When crimping contact DF22A-1012SCF use a press with 3.5 ton min.

Note 2 : AP109A type applicators cannot be used with the CM-105C press.

Note 3 : Any problems that occur from using tools other than those specified by Hirose, are not covered by warranty.

Note 4 : Applicator manufactured by JAPAN AUTOMATIC MACHINE (J.A.M.). Please access to HP of J.A.M., if you make inquiries

about the applicator or crimp defect. (URL : http://www.jam-net.co.jp)

Note 5 : Please follow the "Crimping quality standards" and "Table of crimping conditions" when crimping contacts.

Caution

There are parts on the crimp contact that can cause injuries, please use caution when unmating the contacts.

BCurrent Ratings

The current rating listed in the catalog indicates the allowable current per contact. However, in applications requiring

current transmission through all the contacts, about one-third of the listed rating should be applied.

When the current rating for the connector is 3A, and the allowable current of the conductor being used is 1A, then rating

of 1A will be used for the entire assembly.

The connectors should not be mating / unmating when the electrical current is being applied.

Hot swap should not be performed.

BUsage Environment

Please contact us about use in equipment that is subjected to repetitive high temperature and low temperature

environmental conditions.

Type

Item

Part No.

HRS No.

Applicable Contacts

Automatic

Press unit

CM-105C

901-0001-0

DF22/DF22A-1416SCF/PCF/SCFA

Applicators are used in automatic crimping

machines manufactured by Hirose Electric

AP105-DF22-1416

901-4576-7

DF22-1416SCF/PCF/SCFA/PCFA

AP105-DF22A-1416

901-4578-2

DF22A-1416SCF/PCF/SCFA

Applicators are used in automatic

crimping machines manufactured by

other companies

AP109A-DF22-1416

901-4579-5

DF22-1416SCF/PCF/SCFA/PCFA

AP109A-DF22A-1416

901-4580-4

DF22A-1416SCF/PCF/SCFA/PCFA

AP109A-DF22A-1012

901-4582-0

DF22A-1012SCF/SCFA

Applicator manufactured by

JAPAN AUTOMATIC MACHINE

CHS893800H-UP

-

DF22-1416SCF/DF22-1416PCF

CHS893900H-UP

-

DF22A-1416SCF/DF22A-1416PCF

QHS895800H-UP

-

DF22A-1012SCF

Manual

Crimp tools

HT104/DF22-1416

550-0285-0

DF22-1416SC/PC

HT104/DF22A-1416

550-0286-2

DF22A-1416SC/PC

HT103/DF22A-1012

550-0288-8

DF22A-1012SC

The characteristics and the specifications contained herein are for reference purpose. Please refer to the latest customer drawings prior to use.

The contents of this catalog are current as of date of 01/2016. Contents are subject to change without notice for the purpose of improvements.