| поискавой системы для электроныых деталей |
|
KSZ9031MNX датащи(PDF) 21 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
KSZ9031MNX датащи(HTML) 21 Page - Microchip Technology |
|
21 / 73 page ![]() 2016 Microchip Technology Inc. DS00002096C-page 21 KSZ9031MNX 3.10.2 MII SIGNAL DIAGRAM The KSZ9031MNX MII pin connections to the MAC are shown in Figure 3-5. FIGURE 3-5: KSZ9031MNX MII INTERFACE 3.11 MII Management (MIIM) Interface The KSZ9031MNX supports the IEEE 802.3 MII management interface, also known as the Management Data Input/ Output (MDIO) interface. This interface allows upper-layer devices to monitor and control the state of the KSZ9031MNX. An external device with MIIM capability is used to read the PHY status and/or configure the PHY settings. More details about the MIIM interface can be found in Clause 22.2.4 of the IEEE 802.3 Specification. The MIIM interface consists of the following: • A physical connection that incorporates the clock line (MDC) and the data line (MDIO). • A specific protocol that operates across the physical connection mentioned earlier, which allows an external con- troller to communicate with one or more KSZ9031MNX devices. Each KSZ9031MNX device is assigned a unique PHY address between 0h and 7h by the PHYAD[2:0] strapping pins. • A 32-register address space for direct access to IEEE-defined registers and vendor-specific registers, and for indi- rect access to MMD addresses and registers. See the Register Map section. PHY Address 0h is supported as the unique PHY address only; it is not supported as the broadcast PHY address, which allows for a single write command to simultaneously program an identical PHY register for two or more PHY devices (for example, using PHY Address 0h to set Register 0h to a value of 0x1940 to set Bit [11] to a value of one to enable software power-down). Instead, separate write commands are used to program each PHY device. Table 3-5 shows the MII management frame format for the KSZ9031MNX. TABLE 3-5: MII MANAGEMENT FRAME FORMAT FOR THE KSZ9031MNX Preamble Start of Frame Read/Write OP Code PHY Address Bits [4:0] REG Address Bits [4:0] TA Data Bits [15:0] Idle Read 32 1’s 01 10 00AAA RRRRR Z0 DDDDDDDD_DDDDDDDD Z Write 32 1’s 01 01 00AAA RRRRR 10 DDDDDDDD_DDDDDDDD Z KSZ9031MNX TX _CLK TX _EN TXD[3:0] RX_CLK RX _DV RXD[3:0] MII ETHERNET MAC TX_ER RX _ER CRS COL TX _CLK TX _EN TXD[3:0] RX_CLK RX _DV RXD[3:0] TX_ER RX _ER CRS COL |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |