USB2601 datasheet(15/30 Pages) MICROCHIP

15 / 30 page

 2004 - 2016 Microchip Technology Inc.

DS00002119A-page 15

USB2601/USB2602

General Purpose I/O

Card Power

GPIO8/

CRD_PWR0

I/O8

GPIO: This pin may be used either as input, edge

sensitive interrupt input, or output.

CRD_PWR: Card Power drive of 3.3V @ 100mA.

General Purpose I/O

GPIO9

I/O8

This pin may be used either as input, edge sensitive

interrupt input, or output.

General Purpose I/O

Card Power

GPIO10/

CRD_PWR1

I/O8

GPIO: This pin may be used either as input, edge

sensitive interrupt input, or output.

CRD_PWR: Card Power drive of 3.3V @ 100mA.

General Purpose I/O

Card Power

GPIO11/

CRD_PWR2

I/O8

GPIO: These pins may be used either as input, edge

sensitive interrupt input, or output.

CRD_PWR: Card Power drive of 3.3V @ 200mA.

General Purpose I/O

GPIO[15:12]

I/O8

These pins may be used either as input, or output.

RESET input

RESET_N

This active low signal is used by the system to reset the

chip. The active low pulse should be at least 1

s wide.

TEST Input

TEST

IPD

Used for testing the IC. User must treat either as a no-

connect, or connect to the ground.

USB Transceiver Bias

RBIAS

A 12.0k

,  1.0% resistor is attached from VSS to this

pin, in order to set the transceiver’s internal bias currents.

Analog Test

ATEST

AIO

This signal is used for testing the analog section of the

chip and should be connected to VDDA33 for normal

operation.

Crystal Input/External

Clock Input

XTAL1/

CLKIN

ICLKx

24MHz Crystal or external clock input.

This pin can be connected to one terminal of the crystal

or can be connected to an external 24MHz clock when a

crystal is not used.

Note:

The ‘SEL_CLKDRV and CLK_SEL[1:0]’ pins

will be sampled while RESET_N is asserted,

and the value will be latched upon RESET_N

negation. This will determine the clock source

and value.

Crystal Output

XTAL2

OCLKx

24MHz Crystal

This is the other terminal of the crystal, or left open when

an external clock source is used to drive XTAL1/CLKIN.

It may not be used to drive any external circuitry other

than the crystal circuit.

Select Clock Drive

SEL_CLKDRV

I/O8PD

SEL_CLKDRV. During RESET_N assertion, this pin will

select the operating clock mode (crystal or externally

driven clock source), and a weak pull-down resistor is

enabled. When RESET_N is negated, the value will be

internally latched and the internal pull-down will be

disabled.

‘0’ = Crystal operation (24MHz)

‘1’ = Externally driven clock source (24MHz)

Clock Select

CLK_SEL[1:0]

I/O8PD

SEL[1:0]. During RESET_N assertion, these pins will

select the operating frequency of the external clock, and

the corresponding weak pull-down resistors are enabled.

When RESET_N is negated, the value on these pins will

be internal latched and the internal pull-downs will be

disabled.

SEL[1:0] = ‘00’. 24MHz

SEL[1:0] = ‘01’. RESERVED

SEL[1:0] = ‘10’. RESERVED

SEL[1:0] = ‘11’. RESERVED

ANALOG POWER

1.8V PLL Power

VDD18PLL

1.8V Output from the internal 1.8V PLL regulator

3.3V PLL Power

VDD33PLL

3.3V Input to the internal 1.8V PLL regulator.

Name

Symbol

Buffer Type

Description

USB2601 датащи(PDF) 15 Page - Microchip Technology

USB2601 датащи(HTML) 15 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

датащи скачать

ссылки URL