SC16C554 datasheet(13/55 Pages) PHILIPS

13 / 55 page

Philips Semiconductors

SC16C554/554D

Quad UART with 16-byte FIFO and infrared (IrDA) encoder/decoder

Product data

Rev. 05 — 10 May 2004

13 of 55

9397 750 13132

Functional description

The SC16C554/554D provides serial asynchronous receive data synchronization,

parallel-to-serial and serial-to-parallel data conversions for both the transmitter and

receiver sections. These functions are necessary for converting the serial data

stream into parallel data that is required with digital data systems. Synchronization for

the serial data stream is accomplished by adding start and stop bits to the transmit

data to form a data character. Data integrity is insured by attaching a parity bit to the

data character. The parity bit is checked by the receiver for any transmission bit

errors. The electronic circuitry to provide all these functions is fairly complex,

especially when manufactured on a single integrated silicon chip. The

SC16C554/554D represents such an integration with greatly enhanced features. The

SC16C554/554D is fabricated with an advanced CMOS process to achieve low drain

power and high speed requirements.

The SC16C554/554D is an upward solution that provides 16 bytes of transmit and

receive FIFO memory, instead of none in the 16C454. The SC16C554/554D is

designed to work with high speed modems and shared network environments that

require fast data processing time. Increased performance is realized in the

SC16C554/554D by the larger transmit and receive FIFOs. This allows the external

processor to handle more networking tasks within a given time. In addition, the four

selectable levels of FIFO trigger interrupt and automatic hardware/software ﬂow

control is uniquely provided for maximum data throughput performance, especially

when operating in a multi-channel environment. The combination of the above greatly

reduces the bandwidth requirement of the external controlling CPU, increases

performance, and reduces power consumption.

The SC16C554/554DAI68 combines the package interface modes of the 16C454/554

and 68C454/554 series on a single integrated chip. The 16 mode interface is

designed to operate with the Intel-type of microprocessor bus, while the 68 mode is

intended to operate with Motorola and other popular microprocessors. Following a

reset, the SC16C554/554DAI68 is downward compatible with the 16C454/554 or the

68C454/554, dependent on the state of the interface mode selection pin, 16/68.

The SC16C554/554D is capable of operation to 1.5 Mbit/s with a 24 MHz crystal and

up to 5 Mbit/s with an external clock input (at 3.3 V and 5 V; at 2.5 V the maximum

speed is 3 Mbit/s).

The rich feature set of the SC16C554/554D is available through internal registers.

Automatic hardware/software ﬂow control, selectable transmit and receive FIFO

trigger levels, selectable TX and RX baud rates, infrared encoder/decoder interface,

modem interface controls, and a sleep mode are all standard features. In the

16 mode, INTSEL and MCR[3] can be conﬁgured to provide a software controlled or

continuous interrupt capability. Due to pin limitations of the 64-pin package, this

feature is offered by two different LQFP64 packages. The SC16C554D operates in

the continuous interrupt enable mode by bonding INTSEL to VCC internally. The

SC16C554 operates in conjunction with MCR[3] by bonding INTSEL to GND

internally.

SC16C554 датащи(PDF) 13 Page - NXP Semiconductors

SC16C554 датащи(HTML) 13 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55

датащи скачать

ссылки URL