P89C668 datasheet(48/89 Pages) PHILIPS

48 / 89 page

Philips Semiconductors

Product data

P89C660/P89C662/P89C664/

P89C668

80C51 8-bit Flash microcontroller family

16KB/32KB/64KB ISP/IAP Flash with 512B/1KB/2KB/8KB RAM

2002 Oct 28

S0CON Address = 98H

Reset Value = 0000 0000B

SM0/FE

SM1

SM2

REN

TB8

RB8

Bit Addressable

(SMOD0 = 0/1)*

Symbol

Function

Framing Error bit. This bit is set by the receiver when an invalid stop bit is detected. The FE bit is not cleared by valid

frames but should be cleared by software. The SMOD0 bit must be set to enable access to the FE bit.

SM0

Serial Port Mode Bit 0, (SMOD0 must = 0 to access bit SM0)

SM1

Serial Port Mode Bit 1

SM0

SM1

Mode

Description

Baud Rate**

shift register

fOSC/6 (6 clock mode) or fOSC/12 (12 clock mode)

8-bit UART

variable

9-bit UART

fOSC/32 or fOSC/16 (6 clock mode) or

fOSC/64 or fOSC/32 (12 clock mode)

9-bit UART

variable

SM2

Enables the Automatic Address Recognition feature in Modes 2 or 3. If SM2 = 1 then Rl will not be set unless the

received 9th data bit (RB8) is 1, indicating an address, and the received byte is a Given or Broadcast Address.

In Mode 1, if SM2 = 1 then Rl will not be activated unless a valid stop bit was received, and the received byte is a

Given or Broadcast Address. In Mode 0, SM2 should be 0.

REN

Enables serial reception. Set by software to enable reception. Clear by software to disable reception.

TB8

The 9th data bit that will be transmitted in Modes 2 and 3. Set or clear by software as desired.

RB8

In modes 2 and 3, the 9th data bit that was received. In Mode 1, if SM2 = 0, RB8 is the stop bit that was received.

In Mode 0, RB8 is not used.

Transmit interrupt flag. Set by hardware at the end of the 8th bit time in Mode 0, or at the beginning of the stop bit in the

other modes, in any serial transmission. Must be cleared by software.

Receive interrupt flag. Set by hardware at the end of the 8th bit time in Mode 0, or halfway through the stop bit time in

the other modes, in any serial reception (except see SM2). Must be cleared by software.

NOTE:

*SMOD0 is located at PCON6.

**fOSC = oscillator frequency

SU01451

Bit:

7654

321

Figure 32. S0CON: Serial Port Control Register

P89C668 датащи(PDF) 48 Page - NXP Semiconductors

P89C668 датащи(HTML) 48 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89

датащи скачать

ссылки URL