MCP102-195ESLASHTO datasheet(4/28 Pages) MICROCHIP

4 / 28 page

MCP102/103/121/131

DS20001906D-page 4

 2004-2014 Microchip Technology Inc.

VDD Trip Point

MCP1XX-195

VTRIP

1.872

1.900

1.929

TA = +25°C (Note 1)

1.853

1.900

1.948

TA = -40°C to +85°C (Note 2)

MCP1XX-240

2.285

2.320

2.355

TA = +25°C (Note 1)

2.262

2.320

2.378

Note 2

MCP1XX-270

2.591

2.630

2.670

TA = +25°C (Note 1)

2.564

2.630

2.696

Note 2

MCP1XX-300

2.886

2.930

2.974

TA = +25°C (Note 1)

2.857

2.930

3.003

Note 2

MCP1XX-315

3.034

3.080

3.126

TA = +25°C (Note 1)

3.003

3.080

3.157

Note 2

MCP1XX-450

4.314

4.380

4.446

TA = +25°C (Note 1)

4.271

4.380

4.490

Note 2

MCP1XX-475

4.561

4.630

4.700

TA = +25°C (Note 1)

4.514

4.630

4.746

Note 2

VDD Trip Point Tempco

TTPCO

—

±100

—

ppm/°C

Threshold

Hysteresis

min. = 1%,

max = 6%)

MCP1XX-195

VHYS

0.019

—

0.114

TA = +25°C

MCP1XX-240

0.023

—

0.139

MCP1XX-270

0.026

—

0.158

MCP1XX-300

0.029

—

0.176

MCP1XX-315

0.031

—

0.185

MCP1XX-450

0.044

—

0.263

MCP1XX-475

0.046

—

0.278

RST Low-level Output Voltage

VOL

——

0.4

IOL = 500 µA, VDD =VTRIP(MIN)

RST High-level Output Voltage

(MCP102 and MCP103 only)

VOH

VDD –0.6

—

IOH = 1 mA; for MCP102/MCP103 only

(push-pull output)

Internal Pull-up Resistor

(MCP131 only)

RPU

—95

—



VDD =5.5V

Open-drain High Voltage on Output

(MCP121 only)

VODH

—

13.5 (5)

VVDD =3.0V, Time voltage >5.5V

applied

 100s,

current into pin limited to 2 mA, 25°C

operation recommended

(Note 5, Note 6)

Open-drain Output Leakage Current

(MCP121 only)

IOD

—0.1

—

µA

DC CHARACTERISTICS (CONTINUED)

Electrical Specifications: Unless otherwise indicated, all limits are specified for: VDD = 1V to 5.5V, RPU = 100 k (MCP121 only),

TA = -40°C to +125°C.

Parameters

Sym.

Min.

Typ.

Max.

Units

Conditions

Note

Trip point is ±1.5% from typical value.

Trip point is ±2.5% from typical value.

RST output is forced low. There is a current through the internal pull-up resistor.

This includes the current through the internal pull-up resistor and the reset power-up timer.

This specification allows this device to be used in PIC® microcontroller applications that require In-Circuit Serial

Programming™ (ICSP™) (see device-specific programming specifications for voltage requirements). This specification

DOES NOT allow a continuous high voltage to be present on the open-drain output pin (VOUT). The total time that the

VOUT pin can be above the maximum device operational voltage (5.5V) is 100s. Current into the VOUT pin should be

limited to 2 mA and it is recommended that the device operational temperature be maintained between 0°C to 70°C

(+25°C preferred). For additional information, please refer to Figure 2-33.

This parameter is established by characterization and not 100% tested.

MCP102-195E/TO датащи(PDF) 4 Page - Microchip Technology

MCP102-195E/TO датащи(HTML) 4 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

датащи скачать

ссылки URL