600W with PFC and Parallel Function

WWW.ASTRODYNETDI.COM

ASTRODYNE USA: 1-800-823-8082

ASTRODYNE PACIFIC: 886-2-26983458

INPUT SPECIFICATIONS

Input Voltage Range (Note 3)

90 ~ 264VAC 124~370 Volts(DC)

Frequency Range

47-63Hz

Inrush Current, typ: (cold start)

20Amps/115VAC; 40Amps/230VAC

Input Current

6.8 Amps@115VAC

3.4 Amps@230VAC

Leakage current

< 1.3mAmps / 240VAC

Min Load

See Selection Chart

Power Factor (typ.) @ FL

0.95/230VAC; 0.99/100VAC

OUTPUT SPECIFICATIONS

Voltage and Current

See Selection Chart

Line Regulation

±0.5%

Load Regulation

See Selection Chart

Voltage Tolerance (Note 2)

±2.0%: 5Volts(DC)

±1.0%: 12~48Volts(DC)

Ripple/Noise (Note 1)

180mVpk-pk: 5Volts(DC)

240mVpk-pk: 12~27Volts(DC)

300mVpk-pk: 48Volts(DC)

Hold Up Time @ FL

20mS

Setup, Rise Time @ FL

1500mS, 50mS

Over Voltage Protection

See Selection Chart

Shutdown o/p voltage, re-power

Over Current Protection

105~135% rated output power

Constant Current limiting, auto-recov

Over Temperature Protection

+5Volts(DC): 95°C(TSW1) detect on heatsink of power

transitor; 95°C(TSW51) detect on heatsink of power diode

+12~48Volts(DC): 85°C(TSW1) detect on heatsink of power

transitor; 80°C(TSW51) detect on heatsink of power diode

shutdown o/p voltage, re-power after cool down

DC Voltage Adjust

See Selection Chart

GENERAL SPECIFICATIONS

Safety

UL60950-1,

TUV EN60950-1 Approved

Insulation Resistance

≥100MΩ/500Volts(DC)/25°C/70%RH

EMI

Compliance to EN55022B(CISPR22B)

Harmonic Current

Compliance to EN61000-3-2,-3

Efficiency

See Selection Chart

Isolation

3000VAC Input - Output

1500VAC Input - Ground

500VAC Output - Ground

EMS

Compliance to

EN61000-4-2,3,4,5,6,8,11

ENV50204,

light Industry Level, Criteria A

Remote Control

RC+/RC-: Short=Power ON

Open=Power Off

Pok Signal

PSU turn on: 3.3~5.6Volts(DC)

PSU turn off: 0~1Volts(DC)

ENVIRONMENTAL SPECIFICATIONS

Oper. Temperature

-20°C to +60°C (See Derate Curve)

Storage Temperature

-40°C to +85°C, 10~95% RH

Relative Humidity

20~90% RH, non cond

Temperature Coefficient

±0.03% / °C (0-50°C)

MTBF

116.4KHrs min,MIL-HDBK-217F(25°C)

Vibration

10~500Hz, 2G10min./1cycle, period for

60min. each along X, Y, Z axes

PHYSICAL SPECIFICATIONS

Size

170 x 120 x 93 mm (6.69”x 4.72”x 3.66”)

Weight

67.02 oz (1900g)

NOTE

1. Ripple & noise are measured at 20MHz of bandwidth by using a 12”

twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

2. Tolerance : includes set up tolerance, line regulation and load regula-

tion.

3. Derating may be needed under low input voltages. Please check the

derating curve for more details.

All specifications are typical at nominal input, full load, and 25°C unless other-

wise noted