CPC7692BA datasheet(15/18 Pages) IXYS

15 / 18 page

INTEGRATED CIRCUITS DIVISION

CPC7692

R01

www.ixysic.com

2.5 TSD Pin Description

The TSD pin is a bidirectional I/O structure with an

internal pull-up current source having a nominal value

of 16

A biased from V

DD. As an output, this pin

indicates the status of the thermal shutdown circuitry.

During normal operation, this pin will typically be

pulled up to VDD but under fault conditions that create

excess thermal loading the CPC7692 will enter

thermal shutdown and a logic low will be output.

As an input, the TSD pin is utilized to place the

CPC7692 into the “All-Off” state by simply pulling the

input low. For applications using low-voltage logic

devices (lower than VDD), IXYS IC Division

recommends the use of an open-collector or an

open-drain type output to control TSD. This avoids

sinking the TSD pull up bias current to ground during

normal operation when the all-off state is not required.

In general, IXYS IC Division recommends all

applications use an open-collector or open-drain type

device to drive this pin.

Driving the TSD input to a logic high or tying it to VDD

will not override the thermal shutdown mechanism.

2.6 Ringing Switch Zero-Cross Current Turn Off

After the application of a logic input to turn SW4 off,

the ringing switch is designed to delay the change in

state until the next zero-crossing. Once on, the switch

requires a zero-current cross to turn off, and therefore

should not be used to switch a pure DC signal. The

switch will remain in the on state no matter the logic

input until the next zero crossing. These switching

characteristics will reduce and possibly eliminate

overall system impulse noise normally associated with

ringing switches. See IXYS IC Division’s application

note AN-144, Impulse Noise Benefits of Line Card Access

Switches for more information. The attributes of ringing

switch SW4 may make it possible to eliminate the

need for a zero-cross switching scheme. A minimum

impedance of 300

 in series with the ringing

generator is recommended.

2.7 Power Supplies

Both a +5V supply and battery voltage are connected

to the CPC7692. Switch state control is powered

exclusively by the +5V supply. As a result, the

CPC7692 exhibits extremely low power consumption

during active and idle states.

Although battery power is not used for switch control, it

is required to supply trigger current for the integrated

internal protection circuitry SCR during fault

conditions. This integrated SCR is designed to

activate whenever the voltage at TBAT or RBAT drops 2

to 4 V below the applied voltage on the VBAT pin.

Because the battery supply at this pin is required to

source trigger current during negative overvoltage

fault conditions at tip and ring, it is important that the

net supplying this current be a low impedance path for

high speed transients such as lightning. This will

permit trigger currents to flow enabling the SCR to

activate and thereby prevent a fault induced negative

overvoltage event at the TBAT or RBAT nodes.

2.8 Battery Voltage Monitor

The CPC7692 also uses the VBAT voltage to monitor

battery voltage. If system battery voltage is lost, the

CPC7692 immediately enters the all-off state. It

remains in this state until the battery voltage is

restored. The device also enters the all-off state if the

battery voltage rises more positive than about –10V

with respect to ground and remains in the all-off state

until the battery voltage drops below approximately

–15 V with respect to ground. This battery monitor

feature draws a small current from the battery (less

than 1

A typical) and will add slightly to the device’s

overall power dissipation.

This monitor function performs properly if the

CPC7692 and SLIC share a common battery supply

origin. Otherwise, if battery is lost to the CPC7692 but

not to the SLIC, then the VBAT pin will be internally

biased by the potential applied at the TBAT or RBAT

pins via the internal protection circuitry SCR trigger

current path.

2.9 Protection

2.9.1 Diode Bridge/SCR

The CPC7692 uses a combination of current limited

break switches, a diode bridge/SCR clamping circuit,

and a thermal shutdown mechanism to protect the

SLIC device or other associated circuitry from damage

during line transient events such as lightning. During a

positive transient condition, the fault current is

conducted through the diode bridge to ground via

FGND. Voltage is clamped to a diode drop above

ground. During a negative transient of 2 to 4V more

CPC7692BA датащи(PDF) 15 Page - IXYS Corporation

CPC7692BA датащи(HTML) 15 Page - IXYS Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

датащи скачать

ссылки URL