ASBSM4-LED3 datasheet(144/178 Pages) LUMBERG

144 / 178 page

1-717-217-2299

www.lumberg-automationusa.com

144

Current (I)

This is the rate in which electricity is transferred.

Practical unit is the ampere, which represents the

transfer of one coulomb per second. In a simple

circuit, current (I) produced by a cell or electromotive

force (E) when there is an external resistance (R) and

internal resistance (r) is: I = E / ® + r).

Current Carrying Capacity

The maximum current a conductor can safely

carry without exceeding its insulation and jacket

temperature limitations.

Current Surge

This is a short-term (transient) condition causing

a larger than normal amount of current to flow

through a conductor. A current surge can often cause

damage to an electrical device if it is not

properly protected.

Cut-Through Resistance

The ability of a material to withstand mechanical

pressure, usually a sharp edge or small bend radius,

without separation.

dB (Decibel)

Used to express acoustical power.

DC (Direct Current)

Electrical current that flows in one direction only.

Dielectric Strength

The voltage that an insulator can withstand before

breakdown occurs. Usually expressed as a voltage

gradient (such as volts per mil).

DIN (Deutsches Institut fur Normung)

The German Standardization Institute.

DIN 43650

A German standard, stating the characteristics and

requirements of connectors for magnetic valves used

in hydraulics and pneumatics.

Diode

This is a solid-state electronic component, which will

allow current to flow in only one direction, similar

to a check valve used in hydraulic or pneumatic

applications. The diode is used in applications such

as transient suppression, power supply circuits etc.

Direct Current (DC)

The flow of electrical current in one direction.

Drain Wire

In a cable, the bare wire laid under a metallic foil or

braid and is used as a ground connection.

Distribution Box

Sometimes referred to as Junction or Multi Box is

designed to distribute a signal to multiple locations.

The symbol for Voltage or electromotive force.

Earth

The British term for zero voltage reference.

EFP (Electronic Field Production)

Video production, non-news production, done outside

the studio.

EIA

Electronic Industries Association – formerly RMA

or RETMA.

Electronic Magnetic Sensor

This is a solid-state device, which is used to sense a

magnetic field.

EMF (Electromotive Force)

Voltage

EMI (Electromagnetic Interference)

ENG (Electronic News Gathering)

EPDM (Ethylenepropylenediene Monomer)

A material with good electrical insulating qualities.

EPR (Ethylenepropylene Copolymer Rubber)

A material with good electrical insulating qualities.

ETP (Electrolytic Tough Pitch)

A copper refining process.

EU (European Union Directives)

A copper refining process.

EV (Electron Volt)

Extruded Cable with conductors that are uniformly

insulated and formed by applying a homogeneous

insulation material in a continuous extrusion process.

The symbol for Frequency.

FAS

Fire Alarm and Signal Cable – cable designation.

FEP (Fluorinated Ethylenepropylene)

A thermoplastic material with good electrical

insulating properties and chemical and heat

resistance.

Fillers

Non-conducting components cabled with the

insulated conductors or optical fibers to impart

roundness, flexibility, tensile strength, or a

combination of all three, to the cable.

FM (Frequency Modulation)

Gauss (Ga)

Unit of measure for magnetic flux density.

GHz (Gigahertz)

A unit of frequency equal to 1 billion (109) hertz.

Ground (GND)

An electrical connection between a circuit and earth.

Ground Loop

A completed circuit between shielded pairs of a

multiple pair created by random contact between

shields. Also, is an undesirable circuit condition in

which interference is created by ground currents

when grounds are connected at more than one point.

Ground Potential

A circuit, terminal or chassis is said to be at ground

potential when it is used as a reference point for

other potentials in the system.

Hertz (Hz)

The unit of measure for frequency in cycles per

second.

HF (High Frequency)

The band from 3 to 30 MHz in the radio spectrum.

Hygroscopic

Capable of absorbing moisture from the air.

I2R

Formula for power in watts, where I = current in

amperes, and R = resistance in ohms.

ICEA (Insulated Cable Engineers Association)

IEC (International Electrotechnical Commission)

European Standardization Agency.

IF (Intermediate – Frequency)

IFB (Interrupted Feed Back)

Input

A signal (or power) which is applied to a piece of

References

Glossary of Terms

ASBSM4-LED3 датащи(PDF) 144 Page - Lumberg

ASBSM4-LED3 датащи(HTML) 144 Page - Lumberg

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL