 |
поискавой системы для электроныых деталей |
|
|
поискавой системы для электроныых деталей |
|
PI3CH1010 датащи(PDF) 3 Page - Pericom Semiconductor Corporation |
|
|
|||||||||||||||||||||||||||||
PI3CH1010 датащи(HTML) 3 Page - Pericom Semiconductor Corporation |
|
|
3 / 6 page  ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| 2015-07-0015 PT0470-3 08/05/15 3 PI3CH1010 10-Bit Bus Switch, Enable Low 1.8V/2.5V/3.3V, High-Bandwidth, Hot Plug 1.8V supply (Over operating range, TA = -40 to +85ºC, VCC=1.8V±10%, unless otherwise noted) Symbol Description Test Conditions (1) Min Typ (2) Max Unit VIH Control Input HIGH Voltage Guaranteed Logic HIGH Level 1.2 - VCC+0.3 V VIL Control Input LOW Voltage Guaranteed Logic LOW Level -0.3 - 0.6 V VIK Clamp Diode Voltage VCC = Min., IIN = -18mA - -0.7 -1.8 V IIH Input HIGH Current VCC = Max., VIN = VCC - - ±1 μA IIL Input Low Current VCC = Max., VIN = GND - - ±1 μA IOZH High-Impedance Current 0 ≤ A, B ≤ V CC - - ±1 μA RON Switch On-Resistance (3) VCC = Min., VIN = 0.0V ION = -48mA - 4 8 Ω VCC = Min., VIN = 1.6V ION = -15mA - 10 25 Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC = 1.8V, TA = 25°C ambient and maximum loading. 3. Measured by the voltage drop between A and B pin at indicated current through the switch. On-Resistance is determined by the lower of the voltages on the two (A, B) pins. Capacitance (TA = 25ºC, f=1MHz) Symbol (1) Description Test Conditions Typ (2) Unit CIN Input Capacitance VIN = 0V 2.0 pF COFF A/B Capacitance, Switch Off 3.5 CON A/B Capacitance, Switch On 7.0 Note: 1. These parameters are determined by device characterization but are not production tested Power Supply Characteristics Symbol Description Test Conditions (1) Min Typ Max Unit ICC Quiescent Power Supply Current VCC = 3.6V, VIN = GND or VCC - 0.2 0.5 mA Note: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device. 2. Typical values are at +25°C ambient Dynamic Electrical Characteristics (Over Operating Range, TA = -40 ~ +85ºC, VCC=3.3V±10%) Symbol Description Test Conditions Min Typ Max Unit XTALK Crosstalk 10MHz - -60 - dB OIRR Off-Isolation 10MHz - -60 - BW -3dB Bandwidth See test Diagram - 500 - MHz Switch Characteristics Over 3.3V Operating Range Symbol Description Test Conditions (1) Min Typ Max Unit tPLH, tPHL Propagation Delay (2, 3) Ax to Bx, Bx to Ax See test Diagram - - 0.3 ns tPZH, tPZL Enable Time EN to Ax or Bx See test Diagram 1.5 - 9.0 tPHZ, tPLZ Disable Time EN to Ax or Bx See test Diagram 1.5 - 9.0 |
|
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Russian ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
