LAN8810 datasheet(21/83 Pages) MICROCHIP

21 / 83 page

 2009-2015 Microchip Technology Inc.

DS00001870B-page 21

LAN8810/LAN8810I

is broken). To prevent an unexpected assertion of IRQ, the ENERGYON interrupt mask (INT7_EN)

should always be cleared as part of the ENERGYON interrupt service routine.

Note 3-3

The transmitter FIFO depth can be adjusted via the Transmitter FIFO Depth field of the Extended

Mode Control/Status Register (19.10:9).

3.6

Resets

The device provides the following chip-level reset sources:

• Hardware Reset (nRESET)

• Software Reset

• Power-Down Reset

3.6.1

HARDWARE RESET (NRESET)

A hardware reset will occur when the system reset nRESET input pin is driven low. Anytime nRESET is asserted, it must

be held low for the minimum time specified in Section 5.5.4, "Reset Timing," on page 68 to ensure proper reset to the

PHY. Following a hardware reset, the device resets the device registers and relatches the configuration straps and CON-

FIG[3:0] pins.

On first power-up of the device, the sequence below must be also be followed to ensure the device exits reset in the

correct operational state:

Perform a hardware reset on power-up as per Section 5.5.3, "Power-On Hardware Reset Timing," on page 67.

Wait a minimum of 250mS

Write SMI Register 0 (Basic Control Register) = 0x4040

Wait a minimum of 1 second

Assert the nRESET input pin (nRESET = 0)

Wait a minimum of 50mS

Deassert the nRESET input pin (nRESET = 1)

After completing this sequence, the LAN8810/LAN8810i will be in the default states and ready for any initialization or

configuration and allow operation.

3.6.2

SOFTWARE RESET

A software reset is initiated by writing a ‘1’ to the PHY Soft Reset (RESET) bit of the Basic Control Register. This self-

clearing bit will return to ‘0’ after approximately 256

s, at which time the PHY reset is complete. This reset initializes the

logic within the PHY, with the exception of register bits marked as “NASR” (Not Affected by Software Reset).

Following a software reset, the device configuration is reloaded from the register bit values, and not from the configura-

tion straps and CONFIG[3:0] pins. The device does not relatch the hardware configuration settings. For example, if the

device is powered up and a configuration strap is changed from its initial power up state, a software reset will not load

the new strap setting.

Note:

System implementers should connect the nRESET input pin to an output pin from the respective MAC or

microcontroller, so that the required power-up sequence can be performed without causing a full system

reset event.

Note:

A hardware reset (nRESET assertion) is required following power-up. Refer to Section 5.5.3, "Power-On

Hardware Reset Timing," on page 67 for additional information.

LAN8810 датащи(PDF) 21 Page - Microchip Technology

LAN8810 датащи(HTML) 21 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83

датащи скачать

ссылки URL