CS5336,8,9-K

CS5336-B

CS5336-T

Parameter

Symbol Min Typ Max Min Typ Max Min Typ Max Units

Specified Temperature Range

0

to

70

-40

to

+85

-55

to

+125

°C

Resolution

16

-

-

16

-

-

16

-

-

Bits

Dynamic Performance

Dynamic Range

92.7 95.7

-

90

93.5

-

84

92

-

dB

Signal-to-(Noise + Distortion); THD+N

S/(N+D) 90.7 92.7

-

85

89

-

82

86

-

dB

Signal to Peak Noise

-

96

-

-

95

-

-

94

-

dB

Total Harmonic Distortion

THD

.0025 .001

-

.005 .001

-

.013 .005

-

%

Interchannel Phase Deviation

-

.0001

-

-

.0001

-

-

.0001

-

°

Interchannel Isolation

(dc to 20 kHz)

100 106

-

90

106

-

83

96

-

dB

dc Accuracy

Interchannel Gain Mismatch

-

0.01 0.05

-

.01

.05

-

.01

0.1

dB

Gain Error

(includes Vref tolerance)

-

±1

±5-

±2

±5-

±3

±6%

Gain Drift

(includes Vref drift, Note 1)

-

25

-

-

70

-

-

70

-

ppm/

°C

Bipolar Offset Error

(Note 2)

-

±5 ±15

-

±10 ±30

-

±16 ±65 LSB

Offset Drift

(Note1)

-

15

-

-

20

-

-

20

-

ppm/

°C

rate = 48 kHz; SCLK = 3.072 MHz; Source Impedance = 50

Ω with 10 nF to AGND; Measurement Bandwidth is

10 Hz to 20 kHz; unless otherwise specified.)

Analog Input

Input Voltage Range

(

±Full Scale)

VIN

±3.5 ±3.68 - ±-3.5 ±3.68 -

±3.5 ±3.68 -

V

Input Impedance

ZIN

-

65

-

-

65

-

-

65

-

k

Ω

Power Supplies

Power Supply Current

(VA+)+(VL+)

IA+

-

25

35

-

25

35

-

25

35

mA

with APD, DPD low

VA-

IA-

-

-25

-35

-

-25

-35

-

-25

-35

mA

(Normal Operation)

VD+

ID+

-

30

45

-

30

45

-

30

50

mA

Power Supply Current

(VA+)+(VL+)

IA+

-

10

50

-

10

50

-

10

50

µA

with APD, DPD high

VA-

IA-

-

-10

-50

-

-10

-50

-

-10

-50

µA

(Power-Down Mode)

VD+

ID+

-

10

400

-

10

400

-

10

400

µA

Power Consumption

(APD, DPD Low)

PDN

-

400 575

-

400 575

-

400 600

mW

(APD, DPD High)

PDS

-

0.15 2.5

-

0.15 2.5

-

0.15 2.5

mW

Power Supply

(dc to 26 kHz)

PSRR

-54-

-54-

-54-

dB

Rejection Ratio

(26 kHz to 3.046 MHz)

-

100

-

-

100

-

-

100

-

dB

Notes:

1. This parameter is guaranteed by design and/or characterization.

2. After calibration with DCAL connected to ACAL, and ZEROL & ZEROR terminated to AGND with an

impedance matched to the AINR & AINL source impedance. Executing a calibration with ACAL tied

low (See Power Down and Offset Calibration section) will yield an offset error of typically less than

± 5LSB.

Specifications are subject to change without notice.

CS5336, CS5338, CS5339

3-40

DS23F1