PRODUCT SPECIFICATIONS:

500W ~ 600W AC-DC ACTIVE PFC SWITCHING POWER SUPPLY

PRL1301D DUAL OUTPUT SERIES SPECIFICATION

Input Voltage: 90 ~ 264Vac full range, 47 ~ 63Hz.

Input Current: 8.5A at 90VAC full load.

Inrush Current: 70A peak maximum.(Measuring at 230VAC and full

load cold start.)

Power Factor Correction: Pass EN61000-3-2 class D

Transient Response: Output voltage returns to within 1% in less

than 2.5mS for a 50% load change and the peak transient does not

excess 5%.

Overshoot: Turn-on and turn-off overshoot should not exceed 5%

over nominal voltage.

Efficiency: 80% minimum (Measuring at 115V and full load)

Turn On Delay: 2 second maximum at 115 VAC.

Hold Up Time: 16ms minimum at 115VAC and 75% of rated

maximum load.

Adjustability: Output user adjustable +/-5% minimum.

Remote On-Off: Designated as RSW on the CN3, requires a low

signal to inhibit output.

Power Supply On: When the Bi-color LED emit green light that

indicates the supply is operating. When any protection is occurred or

RSW is applied a low signal, the Bi-color LED will emit orange light.

Power Good: Designated as PG on CN3. This signal will go high

100-500ms after the output reaches the regulation limit. It goes low

at least 1 ms before loss of regulation and has ability to sink 100mA.

Input Circuit Protection (primary): One T10A/250V fuse inserted.

Input Voltage Protection: Power shut down under 80 +/-10Vac, and

recovered over 90 Vac.

Over-Power Protection: Total power limits at 110-140% of the rated

output current and recovers automatically.

Over-Voltage Protection: Output is protected against over voltage.

Unit latching down will occur when Output exceed 130%, and recycle

AC input to reset

Over Temp. Protection: Power supply protected in the event of

excessive operating ambient 110±5 degree C, and automatic

recovery.

Short Circuit Protection: Short circuit can be continuous without

damage and recovers automatically.

Operating Temperature: 0℃ to +50℃

Switching Frequency: 60kHz PFC, 28 kHz PWM.

Storage Temperature: -20 to +85 degrees C.

Operating Humidity: 5% to 90% RH, Non-condensing.

Storage Humidity: 5% to 95% RH, Non-condensing.

Vibration: Frequency 5 to 50 Hz, Acceleration +/-7.35 M/ (SxS) on

X,Y and Z Axis

EMC: CE(EN 55022&EN 55024),FCC(Part 15 Subject J class B,

CISPR 22 class B).

Safety: UL 60950-1,CSA C22.2 No.60950-1,IEC60950-1, CB, TUV.

Leakage Current: The AC leakage current shall not exceed 3.5mA

when the power supply is connected to a supply voltage equal to the

upper limit of the rated voltage range.

HI-POT Test: The power supply shall withstand for 3 Sec without

breakdown the application of a 1500 VAC supply voltage applied

between both input line and chassis (10mA ac cut off current).

Isolating transformers shall withstand 3000VAC applied between

primary and secondary windings and primary to core 1500VAC.

Grounding Test: Apply 25 A current from the ground pin of the three

prong plug to the far most earthed connection point. The maximum

allowable resistance measured during the test is 0.1ohm

Warranty: 2 years.

MTBF: 100000 Hrs (according to MIL-HBK-217F) at 30℃.

Enclosure:

U Type: 8(L) x 5(W) x 1.6(H) inches

E Type: 9(L)☓5(W) ☓1.6(H) inches

F Type: 8(L)☓5(W) ☓ 2 (H) inches

Burn in: 45 +/- 5 degree C for 1 hour @230Vac with full load.

Weight: Max. weight is1600g

Copy Right Ultra Level Tech Co., Ltd 2015, All Right Reserved. Specifications subject to change without notice.

ULTRA LEVEL TECH CO., LTD.

www.ultralevel.com.tw

Tel:+886-2-29180118

Fax:+886-2-29181465

FEATURES:

◆ 600W high power density (Max. 9.3 watts per cubic

inch) with 1U height

◆ Design meets IEC/EN/UL60950-1 Latest Edition

◆ Power Factor Corrected to EN61000-3-2 class D

◆ High Quality & Reliable Component Usage

◆ U-Chassis & Enclosed with built-in fan Mechanical

Options

◆ 5/ 12/ 24V Dual Output Optional Combinations

◆ Full Range AC Input

U type: 8(L) x 5(W) x 1.6(H) inches

F type: 8(L)☓5(W) ☓ 2 (H) inches

E type: 9(L)☓5(W) ☓1.6(H) inches