 |
поискавой системы для электроныых деталей |
|
|
поискавой системы для электроныых деталей |
|
LM46002PWPR датащи(PDF) 3 Page - Texas Instruments |
|
|
|
|||||||||||||||||||||||||||||
LM46002PWPR датащи(HTML) 3 Page - Texas Instruments |
|
|
3 / 52 page  SW VIN PGND CBOOT VCC BIAS SYNC RT PGOOD EN SS/TRK AGND FB SW PGND VIN PAD 1 16 2 3 4 5 6 8 7 9 15 14 13 12 11 10 LM46002 www.ti.com SNVSA13B – APRIL 2014 – REVISED SEPTEMBER 2014 6 Pin Configuration and Functions 16-Pin HTSSOP (PWP) Top View Pin Functions PIN TYPE (1) DESCRIPTION NUMB NAME ER Switching output of the regulator. Internally connected to both power MOSFETs. Connect to power SW 1,2 P inductor. Boot-strap capacitor connection for high-side driver. Connect a high quality 470 nF capacitor from CBOOT CBOOT 3 P to SW. Internal bias supply output for bypassing. Connect bypass capacitor from this pin to AGND. Do not connect VCC 4 P external load to this pin. Never short this pin to ground during operation. Optional internal LDO supply input. To improve efficiency, it is recommended to tie to VOUT when 3.3 V ≤ BIAS 5 P VOUT ≤ 28 V, or tie to an external 3.3 V or 5 V rail if available. When used, place a bypass capacitor (1 to 10 µF) from this pin to ground. Tie to ground when not in use. Clock input to synchronize switching action to an external clock. Use proper high speed termination to SYNC 6 A prevent ringing. Connect to ground if not used. Connect a resistor RT from this pin to AGND to program switching frequency. Leave floating for 500 kHz RT 7 A default switching frequency. Open drain output for power-good flag. Use a 10 k Ω to 100 kΩ pull-up resistor to logic rail or other DC PGOOD 8 A voltage no higher than 12 V. Feedback sense input pin. Connect to the midpoint of feedback divider to set VOUT. Do not short this pin to FB 9 A ground during operation. AGND 10 G Analog ground pin. Ground reference for internal references and logic. Connect to system ground. Soft-start control pin. Leave floating for internal soft-start slew rate. Connect to a capacitor to extend soft SS/TRK 11 A start time. Connect to external voltage ramp for tracking. Enable input to the LM46002: High = ON and Low = OFF. Connect to VIN, or to VIN through resistor EN 12 A divider, or to an external voltage or logic source. Do not float. Supply input pins to internal LDO and high side power FET. Connect to power supply and bypass VIN 13,14 P capacitors CIN. Path from VIN pin to high frequency bypass CIN and PGND must be as short as possible. Power ground pins, connected internally to the low side power FET. Connect to system ground, PAD, PGND 15,16 G AGND, ground pins of CIN and COUT. Path to CIN must be as short as possible. Low impedance connection to AGND. Connect to PGND on PCB. Major heat dissipation path of the die. PAD - - Must be used for heat sinking to ground plane on PCB. (1) P = Power, G = Ground, A = Analog Copyright © 2014, Texas Instruments Incorporated Submit Documentation Feedback 3 Product Folder Links: LM46002 |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Russian ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
