PIC18F010T-ISLASHP datasheet(47/176 Pages) MICROCHIP

47 / 176 page

 2001 Microchip Technology Inc.

Preliminary

DS41142A-page 45

PIC18F010/020

5.3

Reading the Data EEPROM

Memory

To read a data memory location, the user must write the

address to the EEADR register, clear the EEPGD con-

trol bit (EECON1<7>), and then set control bit RD

(EECON1<0>). The data is available in the very next

instruction cycle of the EEDATA register, therefore, it

can be read by the next instruction. EEDATA will hold

this value until another read operation or until it is writ-

ten to by the user (during a write operation).

EXAMPLE 5-1:

DATA EEPROM READ

MOVLW DATA_EE_ADDR

;

MOVWF EEADR

;Data Memory Address to read

BCF

EECON1, EEPGD ;Point to DATA memory

BSF

EECON1, RD

;EEPROM Read

MOVF

EEDATA, W

;W = EEDATA

5.4

Writing to the Data EEPROM

Memory

To write an EEPROM data location, the address must

first be written to the EEADR register and the data writ-

ten to the EEDATA register. Then the sequence in

Example 5-2 must be followed to initiate the write cycle.

EXAMPLE 5-2:

DATA EEPROM WRITE

The write will not initiate if the above required sequence

is not exactly followed (write 55h to EECON2, write

AAh to EECON2, then set WR bit) for each byte. It is

strongly recommended that interrupts be disabled dur-

ing this code segment.

Additionally, the WREN bit in EECON1 must be set to

enable writes. This mechanism prevents accidental

writes to data EEPROM due to unexpected code exe-

cution (i.e., runaway programs). The WREN bit should

be kept clear at all times, except when updating the

EEPROM. The WREN bit is not cleared by hardware

After a write sequence has been initiated, clearing the

WREN bit will not affect the current write cycle. The WR

bit will be inhibited from being set unless the WREN bit

is set. The WREN bit must be set on a previous instruc-

tion. Both WR and WREN cannot be set with the same

instruction.

At the completion of the write cycle, the WR bit is

cleared in hardware and the EEPROM Write Complete

Interrupt Flag bit (EEIF) is set. EEIF must be cleared by

software.

Note:

Do not write to program memory or

EECON1 while writing to EEDATA.

MOVLW

DATA_EE_ADDR

;

MOVWF

EEADR

; Data Memory

Address to write

MOVLW

DATA_EE_DATA

;

MOVWF

EEDATA

; Data Memory

Value to write

BCF

EECON1, EEPGD ; Point to DATA

memory

BSF

EECON1, WREN

; Enable writes

BCF

INTCON, GIE

; Disable

Interrupts

MOVLW

55h

;

Required

MOVWF

EECON2

; Write 55h

Sequence

MOVLW

AAh

;

MOVWF

EECON2

; Write AAh

BSF

EECON1, WR

; Set WR bit to

begin write

BSF

INTCON, GIE

; Enable

Interrupts

SLEEP

; Wait for

interrupt to

signal write

complete

BCF

EECON1, WREN

; Disable writes

PIC18F010T-I/P датащи(PDF) 47 Page - Microchip Technology

PIC18F010T-I/P датащи(HTML) 47 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL