PIC16LC62B datasheet(11/120 Pages) MICROCHIP

11 / 120 page

PIC16C62B/72A

Preliminary

DS35008B-page 11

2.2.2.1

STATUS REGISTER

The STATUS register, shown in Register 2-1, contains

the arithmetic status of the ALU, the RESET status and

the bank select bits for data memory.

The STATUS register can be the destination for any

instruction, as with any other register. If the STATUS

the Z, DC or C bits, the write to these three bits is dis-

abled. These bits are set or cleared according to the

device logic. The TO and PD bits are not writable. The

result of an instruction with the STATUS register as

destination may be different than intended.

For example, CLRF STATUS will clear the upper-three

bits and set the Z bit. This leaves the STATUS register

as 000u u1uu (where u = unchanged).

It is recommended, therefore, that only BCF,

BSF,

SWAPF

and MOVWF instructions are used to alter the

STATUS register, because these instructions do not

affect the Z, C or DC bits from the STATUS register. For

other instructions, not affecting any status bits, see the

"Instruction Set Summary."

STATUS REGISTER (ADDRESS 03h, 83h)

Note 1: The IRP and RP1 bits are reserved. Main-

tain these bits clear to ensure upward

compatibility with future products.

Note 2: The C and DC bits operate as a borrow

and digit borrow bit, respectively, in sub-

traction. See the SUBLW and SUBWF

instructions.

R/W-0

R-1

R/W-x

IRP

RP1

RP0

R = Readable bit

W = Writable bit

U = Unimplemented bit,

read as ‘0’

- n = Value at POR reset

bit7

bit0

bit 7:

IRP: Register Bank Select bit (used for indirect addressing)

(reserved, maintain clear)

bit 6-5: RP1:RP0: Register Bank Select bits (used for direct addressing)

= Bank 1 (80h - FFh)

= Bank 0 (00h - 7Fh)

Each bank is 128 bytes

Note: RP1 is reserved, maintain clear

bit 4:

TO: Time-out bit

= After power-up, CLRWDT instruction, or SLEEP instruction

= A WDT time-out occurred

bit 3:

PD: Power-down bit

= After power-up or by the CLRWDT instruction

= By execution of the SLEEP instruction

bit 2:

Z: Zero bit

= The result of an arithmetic or logic operation is zero

= The result of an arithmetic or logic operation is not zero

bit 1:

DC: Digit carry/borrow bit (ADDWF, ADDLW,SUBLW,SUBWF instructions) (for borrow, the polarity is reversed)

= A carry-out from the 4th low order bit of the result occurred

= No carry-out from the 4th low order bit of the result

bit 0:

C: Carry/borrow bit (ADDWF, ADDLW,SUBLW,SUBWF instructions) (for borrow, the polarity is reversed)

= A carry-out from the most significant bit of the result occurred

= No carry-out from the most significant bit of the result occurred

Note: For borrow, the polarity is reversed. A subtraction is executed by adding the two’s complement of the

second operand. For rotate (RRF, RLF) instructions, this bit is loaded with either the high or low order bit of

the source register.

PIC16LC62B датащи(PDF) 11 Page - Microchip Technology

PIC16LC62B датащи(HTML) 11 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL