LMC7101AIM5 datasheet(5/12 Pages) MICREL

5 / 12 page

September 1999

LMC7101

Micrel

Electrical Characteristics—AC (5V)

V+ = 5V, V– = 0V, V

CM = 1.5V, VOUT = V+/2; RL = 1MΩ; TJ = 25°C, bold values indicate –40°C ≤ TJ ≤ +85°C; unless noted

LMC7101A

LMC7101B

Symbol

Parameter

Condition

Typ

Min

Max

Min

Max

Units

THD

Total Harmonic Distortion

f = 10kHz, A

V = –2,

0.01

L = 2kΩ, VOUT = 4.0 VPP

Slew Rate

0.3

µs

GBW

Gain-Bandwidth Product

0.5

MHz

Electrical Characteristics—AC (12V)

V+ = 12V, V– = 0V, V

CM = 1.5V, VOUT = V+/2; RL = 1MΩ; TJ = 25°C, bold values indicate –40°C ≤ TJ ≤ +85°C; unless noted

LMC7101A

LMC7101B

Symbol

Parameter

Condition

Typ

Min

Max

Min

Max

Units

THD

Total Harmonic Distortion

f = 10kHz, A

V = –2,

0.01

L = 2k, VOUT = 8.5 VPP

Slew Rate

V+ = 12V, Note 10

0.3

0.19

µs

0.15

µs

GBW

Gain-Bandwidth Product

0.5

MHz

Phase Margin

Gain Margin

Input-Referred Voltage Noise

f = 1kHz, V

CM = 1V

nV/ Hz

Input-Referred Current Noise

f = 1kHz

1.5

fA/ Hz

General Notes: Devices are ESD protected; however, handling precautions are recommended. All limits guaranteed by testing on statistical analysis.

Note 1.

Absolute maximum ratings indicate limits beyond which damage to the component may occur. Electrical specifications do not apply when

operating the device outside its recommended operating ratings.

Note 2.

I/O Pin Voltage is any external voltage to which an input or output is referenced.

Note 3.

The maximum allowable power dissipation is a function of the maximum junction temperature, T

J(max); the junction-to-ambient thermal

resistance,

JA; and the ambient temperature, TA. The maximum allowable power dissipation at any ambient temperature is calculated using:

D = (TJ(max) – TA) ÷ θJA. Exceeding the maximum allowable power dissipation will result in excessive die temperature.

Note 4.

Thermal resistance,

JA, applies to a part soldered on a printed-circuit board.

Note 5.

Human body model, 1.5k in series with 100pF.

Note 6.

Common-mode performance tends to follow the typical value. Minimum value limits reflect performance only near the supply rails.

Note 7.

Continuous short circuit may exceed absolute maximum T

J under some conditions.

Note 8.

Shorting OUT to V+ when V+ > 12V may damage the device.

Note 9.

L connected to 5.0V. Sourcing: 5V ≤ VOUT ≤ 12V. Sinking: 2.5V ≤ VOUT ≤ 5V.

Note 10. Device connected as a voltage follower with a 12V step input. The value is the positive or negative slew rate, whichever is slower.

LMC7101AIM5 датащи(PDF) 5 Page - Micrel Semiconductor

LMC7101AIM5 датащи(HTML) 5 Page - Micrel Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12

датащи скачать

ссылки URL