MAX907CSLASHD datasheet(4/12 Pages) MAXIM

4 / 12 page

Single/Dual/Quad High-Speed, Ultra Low-Power,

Single-Supply TTL Comparators

_______________________________________________________________________________________

Note 1:

Trip Point is defined as the input voltage required to make the comparator output change state. The difference

between upper (VTRIP+) and lower (VTRIP-) trip points is equal to the width of the input-referred hysteresis zone (VHYST).

Specified for an input common-mode voltage (VCM) of 0V. See Figure 1.

Note 2:

Input Offset Voltage is defined as the center of the input-referred hysteresis zone. Specified for VCM = 0V. See Figure 1.

Note 3:

Inferred from the CMRR test. Note that a correct logic result is obtained at the output, provided that at least one input is

within the VCMR limits. Note also that either or both inputs can be driven to the upper or lower absolute maximum limit with-

out damage to the part.

Note 4:

Tested with V+ = 5.5V (and V- = 0V for MAX909). MAX909 also tested over the full analog input range (i.e., with

V- = -5.5V).

Note 5:

Tested over the full input voltage range (VCMR).

Note 6:

Specified over the full tolerance of operating supply voltage: MAX907/MAX908 tested with 4.5V < V+ < 5.5V. MAX909

tested with 4.5V < V+ < 5.5V and with -5.5V < V- < 0V.

Note 7:

Positive Supply Current specified with the worst-case condition of all outputs at logic low (MAX907/MAX908), and

with V+ = 5.5V.

Note 8:

Typical power specified with V+ = 5V; maximum with V+ = 5.5V (and with V- = -5.5V for MAX909).

Note 9:

Due to difficulties in measuring propagation delay with 5mV of overdrive in automatic test equipment, the

MAX907/MAX908/MAX909 are sample tested to 0.1% AQL with 100mV input overdrive. Correlation tests show that the

specification can be guaranteed if all other DC parameters are within the specified limits. VOS must be added to the over-

drive voltage for low values of overdrive.

Note 10: Differential Propagation Delay is specified as the difference between any two channels in the MAX907/MAX908 (both out-

puts making either a low-to-high or a high-to-low transition).

Note 11: Propagation Delay Skew is specified as the difference between any single channel’s output low-to-high transition (tPD+)

and high-to-low transition (tPD-), and also between the QOUT and QOUT transition on the MAX909.

Note 12: Latch specifications apply to MAX909 only. See Figure 2.

ELECTRICAL CHARACTERISTICS (continued)

(V+ = 5V, TA = TMIN to TMAX; MAX909 only: V- = 0V, VLATCH = 0V; unless otherwise noted.)

PARAMETER

SYMBOL

CONDITIONS

MIN

TYP

MAX

UNITS

Propagation Delay

tPD+, tPD-

VIN = 100mV, VOD = 5mV

(Note 9)

Differential Propagation Delay

∆tPD

VIN = 100mV, VOD = 5mV

(Note 10)

Propagation Delay Skew

tPDskew

MAX909 only: VIN = 100mV,

VOD = 5mV (Note 11)

Latch Input Voltage High

VIH

(Note 12)

2.0

Latch Hold Time

(Note 12)

Latch Input Voltage Low

VIL

(Note 12)

0.8

Latch Input Current

IIH, IIL

(Note 12)

µA

Latch Setup Time

(Note 12)

MAX907C/D датащи(PDF) 4 Page - Maxim Integrated Products

MAX907C/D датащи(HTML) 4 Page - Maxim Integrated Products

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12

датащи скачать

ссылки URL