LTC1421 datasheet(18/24 Pages) LINER

18 / 24 page

LTC1421/LTC1421-2.5

APPLICATIONS INFORMATION

Figure 23 shows how to use the LTC1421 with a 5V supply

and an LTC1430CS8 synchronous step-down switching

regulator to generate 3.3V output at up to 10A for micro-

processors. Resistors R4, R8 and R9 set the turn-on

voltage at 4.8V and the turn-off at 4.25V. Pushbutton

switch S1 provides users a way to reset the output while

S2 is used to soft-reset the microprocessor only.

Figure 24 shows how to use the LTC1421 with a 5V supply

and a – 48V supply that is used to generate a

±12V supply

using a supply module. Resistors R3 and R4 are used to

monitor the input voltage to the supply module. The

module is prevented from turning on via the optoisolator

until the input voltage reaches – 36V. Zener diode D2

prevents the CPON pin of the LTC1421 from being dam-

aged by excessive voltage.

Figure 25 shows how to use the LTC1421 to do overvolt-

age protection. Resistors R3 and R4 set the trip point at

7V. When the input supply voltage rises above 7V, Q2 is

turned on and Q1 turned off while Q3 helps to discharge

the output voltage.

Figure 26 shows how to use the LTC1421 to control both

the power-up and power-down sequence of the outputs.

The 5V output would be powered up first followed by the

3V output. At power-down sequence, the 3V output would

go down first followed by the 5V supply.

Figure 27 shows how to use the LTC1421 to switch 3.3V,

5V, 12V and –12V supplies for PCI application. The ramp-

up rate for 3.3V, 5V and 12V is determined by the ramp

capacitor C2 while the –12V supply is controlled by R7 and

C3. The internal comparator is being used to do the

overcurrent protection for Q4 with the trip point set by

resistors R6 and R8. The –12V supply does not have

overcurrent protection. R10 is used to set the power good

signal trip point at 10V. When the 12V output rises above

10V, the PCI controller gets a power good signal followed

by RESET after 200ms.

module. The ground pin for the LTC1421 is connected to

– 48V; Zener diode D1 and resistor R1 provide the positive

supply for the chip. Bypass capacitor C4 is protected

against inrush current by P-channel Q1. When the board

is inserted into the backplane, transistor Q1 is turned off

by resistor R2. When the connection sense pins, CON1

and CON2 have been connected to – 48V for more than

20ms, CPON pulls high turning on Q2 and the gate of Q1

starts to pull low with a time constant determined by R2,

R3 and C3. At the same time, the voltage at the input to the

power module starts to ramp up. When the voltage across

the inputs to the power module reaches the comparator

trip level set by R5 and R6, in this case – 32V, the

comparator output pulls high and turns on the 5V supply.

A cheaper solution is shown in Figure 20 using the

®1170HV switcher. Again P-channel transistor Q1 pro-

tects the bypass capacitors against inrush current and

resistors R5 and R6 set the comparator trip voltage. The

LT1170HV is turned on via the VC pin. Resistors R11, R14

and transistor Q4 provide a monitoring path for the RESET

signal which is level shifted up to 5V through an optoiso-

lator.

The P-channel power FET is being replaced by an

N-channel FET in Figure 21 for the – 48V application.

Again, Zener Diode D1 and resistor R1 provide the positive

supply for the chip. Capacitor C1 is to insure Q1 stays off

when the board is being hot inserted into the backplane.

The resistor divider R1 and R2, along with the internal

comparator, perform the undervoltage lock out function.

Q1 would only be turned on when the input supply voltage

is lower than – 42V. The power module would then be

turned on by the optoisolator, 4N25, when the module’s

input voltage reaches 47V.

Figure 22 shows how to use the LTC1421 with a 24V

supply and a LT1074CT step-down switcher. Resistors R5

and R6 set the turn-on threshold to 22V. All of the

supervisory signals can be used without level shifting.

LTC1421 датащи(PDF) 18 Page - Linear Technology

LTC1421 датащи(HTML) 18 Page - Linear Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

датащи скачать

ссылки URL