LT1330CSW datasheet(3/8 Pages) LINER

3 / 8 page

LT1330

PARAMETER

CONDITIONS

MIN

TYP

MAX

UNITS

Any Driver

Output Voltage Swing

Load = 3k to GND

Positive

5.0

7.5

Negative

– 6.3

– 5.0

Logic Input Voltage Level

Input Low Level (VOUT = High)

1.4

0.8

Input High Level (VOUT = Low)

2.0

1.4

Logic Input Current

0.8V

≤ VIN ≤ 2V

520

µA

Output Short-Circuit Current

VOUT = 0V

±917

Output Leakage Current

Shutdown VOUT = ±30V (Note 5)

100

µA

Data Rate (Note 8)

RL = 3k, CL = 2500pF

120

kBaud

RL = 3k, CL = 1000pF

250

kBaud

Slew Rate

RL = 3k, CL = 51pF

µs

RL = 3k, CL = 2500pF

µs

Propagation Delay

Output Transition tHL High to Low (Note 6)

0.6

1.3

µs

Output Transition tLH Low to High

0.5

1.3

µs

Any Receiver

Input Voltage Thresholds

Input Low Threshold (VOUT = High)

0.8

1.3

Input High Threshold (VOUT = Low)

1.7

2.4

Hysteresis

0.1

0.4

1.0

Input Resistance

VIN = ±10V

Ω

Output Leakage Current

Shutdown (Note 5) 0

≤ VOUT ≤ VCC

110

µA

Receivers 1, 2, 3, 4

Output Voltage

Output Low, IOUT = – 1.6mA

0.2

0.4

Output High, IOUT = 160µA (VL = 3V)

2.7

2.9

Output Short-Circuit Current

Sinking Current, VOUT = VCC

– 10

– 20

Sourcing Current, VOUT = 0V

Propagation Delay

Output Transition tHL High to Low (Note 7)

250

600

Output Transition tLH Low to High

350

600

Receiver 5 (LOW Q-Current RX)

Output Voltage

Output Low, IOUT = – 500µA

0.2

0.4

Output High, IOUT = 160µA (VL = 3V)

2.7

2.9

Output Short-Circuit Current

Sinking Current, VOUT = VCC

–2

–4

Sourcing Current, VOUT = 0V

Propagation Delay

Output Transition tHL High to Low (Note 7)

µs

Output Transition tLH Low to High

µs

ELECTRICAL C

HARA TERISTICS (Note 2)

The q denotes specifications which apply over the operating temperature

range (0

°C ≤ TA ≤ 70°C for commercial grade, and –40°C ≤ TA ≤ 85°C for

industrial grade).

Note 1: Absolute Maximum Ratings are those values beyond which the life

of the device may be impaired.

Note 2: Testing done at VCC = 5V and VON/OFF = 3V.

Note 3: Supply current is measured as the average over several charge

pump burst cycles. C+ = 1.0

µF, C– = 0.1µF, C1 = C2 = 0.2µF. All outputs

are open, with all driver inputs tied high.

Note 4: VL supply current is measured with all receiver outputs low.

Note 5: Measurements in shutdown are performed with VON/OFF ≤ 0.1V.

Supply current measurements using driver disable are performed with

VDRIVER DISABLE ≥ 3V.

Note 6: For driver delay measurements, RL = 3k and CL = 51pF. Trigger

points are set between the driver’s input logic threshold and the output

transition to the zero crossing (tHL = 1.4V to 0V and tLH = 1.4V to 0V).

Note 7: For receiver delay measurements, CL = 51pF. Trigger points are

set between the receiver’s input logic threshold and the output transition

to standard TTL/CMOS logic threshold (tHL = 1.3V to 2.4V and tLH = 1.7V

to 0.8V).

Note 8: Data rate operation guaranteed by slew rate, short-circuit current

and propagation delay tests.

LT1330CSW датащи(PDF) 3 Page - Linear Technology

LT1330CSW датащи(HTML) 3 Page - Linear Technology

Html Pages

1 2 3 4 5 6 7 8

датащи скачать

ссылки URL