HIP9010 datasheet(3/12 Pages) INTERSIL

3 / 12 page

4-3

Absolute Maximum Ratings

Thermal Information

DC Logic Supply, VDD . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to +7.0V

Output Voltage, VO . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to +7.0V

Input Voltage, VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +7V (Max)

Operating Conditions

Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to 125oC

Thermal Resistance (Typical, Note 1)

JA (

oC/W)

SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

115

Maximum Storage Temperature Range, TSTG . . . . -65

oC to 150oC

Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . .150oC

Maximum Lead Temperature (Soldering) . . . . . . . . . . . . . . . 300oC

At distance 1/16in

± 1/32in (1.59mm ± 0.79mm) from case

for 10s (Max)

(SOIC - Lead Tips Only)

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operationofthe

device at these or any other conditions above those indicated in the operational sections of this speciﬁcation is not implied.

NOTE:

θJA is measured with the component mounted on an evaluation PC board in free air.

Electrical Speciﬁcations VDD = 5V, ±5%, GND = 0V, Clock Frequency 4MHz, ±0.5%, TA = -40oC to 125oC,

Unless Otherwise Speciﬁed

PARAMETER

SYMBOL

TEST CONDITIONS

MIN

TYP

MAX

UNITS

DC ELECTRICAL CHARACTERISTICS

Quiescent Supply Current

IDD

VDD = 5.25V, GND = 0V

7.5

Midpoint Voltage, Pin 3

VMID

VDD = 5.0V, IL = 2mA Source

2.3

2.45

2.55

Midpoint Voltage, Pin 3

VMID

VDD = 5.0V, IL = 0mA

2.4

2.5

2.6

Input Leakage, Pin 14

ILTEST

Measured at VDD = 5.0V

µA

Internal Pull-Up Resistance, Pin 14

RTEST

VDD = 5.0V, I Measure = 15µA

100

200

Ω

Leakage of Pins 7, 8, 12 and 13

Measured at GND and VDD = 5V

±3

µA

Low Input Voltage, Pins 7, 8, 12 and 13

VIL

% of VDD

High Input Voltage, Pins 7, 8, 12 and 13

VIH

% of VDD

Low Level Output, Pin 11

VOL

ISOURCE = 4mA

0.01

0.30

Leakage Pin 11

Measured at GND and VDD = 5V

±10

µA

Low Level Output, Pin 10

VOL

ISOURCE = 500µA, VDD = 5V

1.5

High Level Output, Pin 10

VOH

ISINK = -500µA, VDD = 5V

4.4

INPUT AMPLIFIERS

S0FB and S1FB High Output Voltage

VOUTHI

100

µA ISINK, VDD = 5V

4.7

4.9

S0FB and S1FB Low Output Voltage

VOUTLO

100

µA ISOURCE, VDD = 5V

200

S0FB and S1FB Closed Loop

ACL

Input Resistor = 1M

Ω,

Feedback Resistor = 49.9k

Ω

-25

-26

-27

S0FB and S1FB Closed Loop

ACL

Input Resistor = 47.5k

Ω,

Feedback Resistor = 475k

Ω

ANTIALIASING FILTER

Response 1kHz to 20kHz,

Referenced to 1kHz

Test Mode, 70mVRMS Input to S0FB or

S1FB, Output Pin 4

--2-

Attenuation at 180kHz

Referenced to 1kHz

ATEN

Test Mode, 70mVRMS Input to S0FB or

S1FB, Output Pin 4

-10

-15

PROGRAMMABLE FILTERS

Peak to Peak Voltage Output

VOUTP-P

Run Mode

3.5

4.0

VP-P

Filters Q (Note 2)

Run Mode

2.5

PROGRAMMABLE GAIN AMPLIFIERS

Percent Amplifier Gain Deviation

Per Table 2

Run Mode

±1-

HIP9010

HIP9010 датащи(PDF) 3 Page - Intersil Corporation

HIP9010 датащи(HTML) 3 Page - Intersil Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12

датащи скачать

ссылки URL