HIP4080AIP datasheet(3/15 Pages) INTERSIL

3 / 15 page

Speciﬁcations HIP4080A

Absolute Maximum Ratings

Thermal Information

Supply Voltage, VDD and VCC. . . . . . . . . . . . . . . . . . . . -0.3V to 16V

Logic I/O Voltages . . . . . . . . . . . . . . . . . . . . . . . -0.3V to VDD +0.3V

Voltage on AHS, BHS . . . . -6.0V (Transient) to 80V (25oC to 125oC)

Voltage on AHS, BHS . . . -6.0V (Transient) to 70V (-55oC to 125oC)

Voltage on ALS, BLS . . . . . . . -2.0V (Transient) to +2.0V (Transient)

Voltage on AHB, BHB . . . . . . . . . VAHS, BHS -0.3V to VAHS, BHS +VDD

Voltage on ALO, BLO . . . . . . . . . . . . . VALS, BLS -0.3V to VCC +0.3V

Voltage on AHO, BHO . . . . . . . VAHS, BHS -0.3V to VAHB, BHB +0.3V

Input Current, HDEL and LDEL . . . . . . . . . . . . . . . . . . -5mA to 0mA

Phase Slew Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20V/ns

NOTE: All Voltages relative to VSS, unless otherwise speciﬁed.

Thermal Resistance

SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

+85oC/W

DIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

+75oC/W

Maximum Power Dissipation at +85oC

SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 470mW

DIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 530mW

Storage Temperature Range . . . . . . . . . . . . . . . . . . -65oC to +150oC

Operating Max. Junction Temperature . . . . . . . . . . . . . . . . . +125oC

Lead Temperature (Soldering 10s) . . . . . . . . . . . . . . . . . . . . +300oC

(For SOIC - Lead Tips Only)

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation

of the device at these or any other conditions above those indicated in the operational sections of this speciﬁcation is not implied.

Operating Conditions

Supply Voltage, VDD and VCC. . . . . . . . . . . . . . . . . . . +9.5V to +15V

Voltage on ALS, BLS . . . . . . . . . . . . . . . . . . . . . . . . . -1.0V to +1.0V

Voltage on AHB, BHB . . . . . . . . . . VAHS, BHS +5V to VAHS, BHS +15V

Input Current, HDEL and LDEL. . . . . . . . . . . . . . . . -500

µA to -50µA

Operating Ambient Temperature Range . . . . . . . . . . -40oC to +85oC

Electrical Speciﬁcations

VDD = VCC = VAHB = VBHB = 12V, VSS = VALS = VBLS = VAHS = VBHS = 0V, RHDEL = RLDEL = 100K, and

TA = +25

oC, Unless Otherwise Speciﬁed

PARAMETERS

SYMBOL

TEST CONDITIONS

TJ = +25

TJ = - 40

TO +125oC

UNITS

MIN

TYP

MAX

MIN

MAX

SUPPLY CURRENTS AND CHARGE PUMPS

VDD Quiescent Current

IDD

IN- = 2.5V, Other Inputs = 0V

VDD Operating Current

IDDO

Outputs switching f = 500kHz, No Load

VCC Quiescent Current

ICC

IN- = 2.5V, Other Inputs = 0V,

IALO = IBLO = 0

100

µA

VCC Operating Current

ICCO

f = 500kHz, No Load

1.25

2.0

0.8

AHB, BHB Quiescent Current -

Qpump Output Current

IAHB, IBHB

IN- = 2.5V, Other Inputs = 0V, IAHO =

IBHO = 0, VDD = VCC =VAHB = VBHB = 10V

-50

-25

-11

-60

-10

µA

AHB, BHB Operating Current

IAHBO,IBHBO f = 500kHz, No Load

0.62

1.2

1.5

0.5

1.9

AHS, BHS, AHB, BHB Leakage Current

IHLK

VBHS = VAHS = 80V,

VAHB = VBHB = 93V

0.02

1.0

µA

AHB-AHS, BHB-BHS Qpump

Output Voltage

VAHB - VAHS

VBHB - VBHS

IAHB = IAHB = 0, No Load

11.5

12.6

14.0

10.5

14.5

INPUT COMPARATOR PINS: IN+, IN-, OUT

Offset Voltage

VOS

Over Common Mode Voltage Range

-10

+10

-15

+15

Input Bias Current

IIB

0.5

µA

Input Offset Current

IOS

-1

-2

µA

Input Common Mode Voltage Range

CMVR

VDD

-1.5

1VDD

-1.5

Voltage Gain

AVOL

V/mV

OUT High Level Output Voltage

VOH

IN+ > IN-, IOH = -250µAVDD

-0.4

VDD

- 0.5

-V

OUT Low Level Output Voltage

VOL

IN+ < IN-, IOL = +250µA

0.4

0.5

Low Level Output Current

IOL

VOUT = 6V

6.5

High Level Output Current

IOH

VOUT = 6V

-17

-10

-3

-20

-2.5

INPUT PINS: DIS

Low Level Input Voltage

VIL

Full Operating Conditions

1.0

0.8

High Level Input Voltage

VIH

Full Operating Conditions

2.5

2.7

Input Voltage Hysteresis

Low Level Input Current

IIL

VIN = 0V, Full Operating Conditions

-130

-100

-75

-135

-65

µA

High Level Input Current

IIH

VIN = 5V, Full Operating Conditions

-1

-10

+10

µA

HIP4080AIP датащи(PDF) 3 Page - Intersil Corporation

HIP4080AIP датащи(HTML) 3 Page - Intersil Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

датащи скачать

ссылки URL